Jump to content
SAU Community

Recommended Posts

As stated above, i want to know what will happen to the turbo *if anything* if i remove the stock BOV and block up the pipes it carries.

As far as im aware the RB20DET that comes in the cefiro does not have a BOV stock. (Can someone confirm or deny this)

Will it shorten the life of the turbo? cause damage to fins etc etc? Can it snap the exhaust wheel off?

I have a front mount, SAFC II, fuel pump, 3" turbo back.

Anyone?

yeh, like he said, it's not easy to prove for or against, but i mean, many cars block em and last for ages.. Blocking mine stopped the surging i was experiencing in between gear changes.. only problem is the noise, but it's not very audible with stock box on

realistically it'll probably cut your turbo life by about 10 minutes.

YEah doubt itll do much i dont have one and my car is an auto so its always got full boost when it goes through the gears still no damage no end play everything excellent was worried about it when i bought mine but after reading a few threads on SAU couldnt find any thing that made me think i should put one on post-30197-1169037152.jpg

I have a RB20DET and blocked off the standard BOV. It worked really well, sounded good and gear changing felt quicker. Although it started to stall on me every now and then. Revs would just drop down when i changed gears, was very werid. When i put the stock BOV back on car worked fine again. Anyone know why this would happen?

Thanks :laugh:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...