Jump to content
SAU Community

Clicking Sound at startup

GTST4G

By GTST4G,
in Engines & Forced Induction

 Share

Recommended Posts

GTST4G Enthusiast

GTST4G

Posted
Posted

Hey guys,

has anyone ever had a clicking sound at startup, that lasts for approx 2 sec and then stops. I'm thinking its got something to do with the starter motor - maybe the shaft needs lubrication or something? I'm worried it may need a complete overhaul?

Any of you guys ever had a similar thing happen?

Cheers

G

Link to comment
https://www.sau.com.au/forums/topic/1530-clicking-sound-at-startup/
Share on other sites
Zahos Mentor

Zahos

Posted
Posted

I also get a weird sound, but it sounds like a different problem. Mine comes on after cranking it over and it has started. Sounds like something squeeking under the car, and I cant tell if it is coming from the front or the back! My only guess so far it that it is the fuel pump....

Jay95R33 Grand Master

Jay95R33

Posted
Posted

I have this sound when I start it first thing in the mornings.

I crank it, it starts, then you hear click click.

I 'think' I know how not to make the noise. This morning I was running mega low on fuel - on the E mark.

So I thought I'd let the fuel pump prime the system well before I started her up.

I put it in the 'ON' position for about 5 seconds until the fuel pump stopped priming, then started it up. And there wasn't any clicking noises !!!!

I have no idea what the clicking is, but try doing the above before you start her up.

Worth a try.

J

blind_elk Grand Master

blind_elk

Posted
Posted

Wondering if it might not be a noisy lifter (RBs have hydraulic lifters, I think). Disappears because the oil pressure comes up to normal. Does it do it once the engine gets up to temp, say you stopped at the corner shop for something?

john Enthusiast

john

Posted
Posted
Originally posted by Zahos

I also get a weird sound, but it sounds like a different problem. Mine comes on after cranking it over and it has started. Sounds like something squeeking under the car, and I cant tell if it is coming from the front or the back! My only guess so far it that it is the fuel pump....

yer i have the same thing, a very faint clicking noise on idle, i have no idea what it is

Cubes Grand Master

Cubes

Posted
Posted

I had a slight lifter noise when starting.

I began using a thinner oil (Mobil 1) and it has now stopped the lifter noise.

Also try doing an oil change after 2000km's with an oil filter and see if it helps - drop the oil while it is hot.

Then make sure you always do an oil change every 5000km's with an oil filter to prevent little gritty crappy bits getting in to the pump up hydraulic lifters.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Dose Pipe Sutututu
      new 1.5 LSD issues/concerns

      By Dose Pipe Sutututu · Posted

      Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...