Jump to content
SAU Community

Recommended Posts

I'm looking to buy a pair of seats from Just Jap that come only with "universal rails". Supposedly they need to be "modified and adapted" to fit my S1 2dr R33 gts-t

I just have a number of questions that I need answered before i go ahead with the purchase:

What is involved in modifying the rails? Is it something I can do myself?

If not, then how much (on average) would I be expecting to pay someone to fit them?

Has anybody here who has modified these rails themselves give me some insight into it please!

Thanks guys

Edited by Mike_
Link to comment
https://www.sau.com.au/forums/topic/153345-universal-rail-modification/
Share on other sites

i hope you find a pretty cheap way to do it!.. i really wana buy those bride copy leather seats from justjap. but last time i heard to get rails modified was around 600 :P

Around $300 per side is fairly reasonable IMHO - You can still end up with a good set of brand new seats fitted for under $1000 which is pretty decent.

Basically, it's a real bitch of a job.

What you have to do, is end up with some combination of the oringal rails mated with the universal rails.

It's totally bogey. Requires welding and cutting. If you don't ahve a welder, drill, grinder, I wouldn't even think about trying it yourself.

If you have a look in the for sale section, you can buy bride rails second hand for pretty cheap. like maybe 200 each. They're much better.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...