Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

mine is costing over $7,000. the bottom end should be capable of 700-800hp i would guess specially with the inturnals they have put in it. with the proper bold on mods etc. but thats just a guess at the moment. running around 18psi i have been told that i possibly make 300-320rwkw

hey tangles, im getting the motor in the 260 rebuilt at the moment, to make a short story its costing me about $5500. Oh and cos i dont get it back for about a month i got bored and bought a 97 RS4 from nsw, should get it friday!

You're a madman Ben - I like your style.

Rebuild due to "issues" or purely precautionary?

mine is costing over $7,000. the bottom end should be capable of 700-800hp i would guess specially with the inturnals they have put in it. with the proper bold on mods etc. but thats just a guess at the moment. running around 18psi i have been told that i possibly make 300-320rwkw

hey fella

i didnt get a chance to have a look as i was running late..

out of curiosity what does $7+ k buy you these days?

and where are BDT getting the machining done?

whats included in the total build up from BDT?

You almost had me? You never had me - you never had your car... Granny shiftin' not double clutchin' like you should. You're lucky that hundred shot of NOS didn't blow the welds on the intake! You almost had me?

You almost had me? You never had me - you never had your car... Granny shiftin' not double clutchin' like you should. You're lucky that hundred shot of NOS didn't blow the welds on the intake! You almost had me?

hmmmmm....focken air con has died in my bedroom...grrrr

stupid airwell shieeet

chops the engine rebuild was due to the car dropping the bottom.

danderman4 not too sure where they got the engine machining work done but ill find out, i have asked 1 guy(1 of the apprentices) and he wasnt exactly sure.

the build from bottom up is that i can remember:

sump baffle kit

new oil and water pumps

gates timing belt

acl race series bearings, pistons(20 thou over), rings and gasket kit

eagle h beam rods

aero speed cam gears

new complete engine hose kit

new head bolts

work which was done on the head and block(not sure what was done off the top of my head what they did)

thats about it that i can remember for now. i know there is still 2 engine mounts getting done and the abs unit is getting replaced

Edited by Turbz_13

well it is nearly time for me to get my car back. and i cant wait!

post-14265-1170457962.jpg

appart form jake riding my engine very thing else is looking nice!

now i just gotta grab me a abs unit and it will all be sweet as!! organise rego and away we go!! woohoo

the engine is bolted back to the gear box and hopefully is going it be in and started this week!

so hopefully i will be out on the next cruse that is held around adelaide.

Edited by Turbz_13
You're a madman Ben - I like your style.

Rebuild due to "issues" or purely precautionary?

Ha ha! Thanks chops!

Rebuild is due to issues, basic issue being i blew a turbo seal and it syphoned all the oil out of the motor and did in the bottom end! Not happy, but what can ya do, atleast it will be built stronger and i will know what condition the motor is in!

Got my RS4 on the weekend, not in bad nick, needs a few things cleaned up but isnt bad for the price i got it for. Now i realise the difference between an RS4 and a 260RS though...lol, funny how they dont go aswell with only one turbo! lmao!

Ha ha, no drifty's yet, its still cleanish so i stick to the bitumen, once its ready for a wash ill go for a spin on the dirt!

Not going to bad otherwise, considering its an auto 25 that is! lmao! Will feel funny when i get the 260 back!

yes, got the abs unit from the good guys down at nisswreck, thanks guys!! get that up 2 blackwood asap and hopefully i got me car next week!! woohoo can wait!!!! cant wait to come on another cruse with you guys!!

Edited by Turbz_13
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...