Jump to content
SAU Community

New guy...


Guest Skyline Fan 01

Recommended Posts

Guest Skyline Fan 01

Hey everyone,

I'm new to this whole forum thing, so I've got no idea really what i'm doing. Guess i'm just tryin to find my way around.

One thing is i know basically next to nothing about cars. That is, the insides of them, like engine specs and all that. So, if anyone can give me a run-down of what all the fancy terms mean, then that'd be nice.

If any1 has any pointers 4 me about forums (this 1 in particular obviously) then it'd be greatly appreciated.

Also, I've got around 17-20k for my first car. Any suggestions?....Doesn't matter what. Doesn't have 2b a Skyline necessarlily.....but preferably, of course.

Anyway, thanks heaps.

Link to comment
https://www.sau.com.au/forums/topic/15359-new-guy/
Share on other sites

  • Replies 43
  • Created
  • Last Reply

Top Posters In This Topic

if u arent really concerned about what car u get then you should just consider the economic and use factor, will u use it everyday, how far will u travel etc. Skylines do tend to be a bit heavy on the ocket for petrol, specially if u just lurrrve pushing that accelarator. i suggest sum front wheel drive toy, good fun, handbrakies are good fun too hehe

Link to comment
https://www.sau.com.au/forums/topic/15359-new-guy/#findComment-314624
Share on other sites

Guest Skyline Fan 01

ok cool......thanks for that everyone....that kinda gets me started in the right direction. At least i've got some idea of what to look for now.

I'm still not sure how much i'll have to spend, cause i'll have to wait as the olds are tradin' in mums 2001(?) pulsar +, so i'll have to just see, but that's the rough amount.....

And i'll definately be asking about what some terms mean, cause my friends know their car jargon, but like i said, i've got no idea, so thanks heaps for that as well.

Also, what's the easiest way to tell the difference between the R33 and R34 Skylines?

Link to comment
https://www.sau.com.au/forums/topic/15359-new-guy/#findComment-315111
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The downside of this is when you try to track the car, as soon as you hit ABS you get introduced to a unbled system. I want to avoid this. I do not want to bleed/flush/jack up the car twice just to bleed the f**kin car.
    • But again, the engineers said your cast aluminium would be fine based on the load that would be stretching that section. Same load stretching the bolts in a flex (not the twist), with a much smaller cross sectional area than the original part you've broken. It's why you'd need to be using higher strength bolts, but that's just making up for the strength you lose with less area...
    • I am truly amazed someone on this planet was able to cycle the pump using a scan tool. I've always ghetto cycled them on Nissan 90s shit boxes by slamming the brakes and pulling the handbrake to agitate the rear wheels enough to cause a speed difference
    • I didn't actually try it at the time but a Launch X431 with the appropriate software licenses/upsell will have the ABS bleed function. The Consult II you can still find some old sets of equipment but they're really, really expensive:   
    • Well I'll start by saying I'm not an engineer. I am going to go with the KiwiCNC ones.  They are made of 7050 alloy have good fillets and radius.  The material alone is in the order of double the strength and fatigue resistance - Those bolts, once torqued correctly place most of the load at the flat face of the mating surface - the 'stretch' you're talking about through torqueing them up would be far more than the extra stretch 'load' placed on them from a steering input or bump. (in my opinion) so I doubt they would flinch.    - but again "not an engineer".      oh and I don't think stitch welding 7050 is a good idea, likely just weaken the material (from what I read)
×
×
  • Create New...