Jump to content
SAU Community

Recommended Posts

how is it only 1 in 10 are suitable? arent the blocks all made the same? or individually cast.....lol but seriously hows that possible?

RE: Oil Squirters

My RB30E block apparently didn't have enough wall thickness to tap in to.

Edited by conan7772
We've got a na r31 rb30 skyline bottom end @ home with piston oil squirters (conrod). Might be one of the rare ones?

There not piston oil squirters.. They squirt a little oil on the load side of the bore. :P

Check the rb30 guide for a pic of piston crown oil squirters.

I need to find the bloke who stated the rb30et blocks have oil squirters... Thread was around here some where.

Yeah I saw that thread too, but they definatly don't - only way is if someone has put them in afterwards.

Yeah, I have an ET block floating around here somewhere actually. :)

But anyway, I actually called up boostworx today, if only I could find some s2 coilpacks or an S1 loom I'd be in business almost. Pretty much taking it down there next week anyway, with the instructions not to call me until its running because I'm sick of seeing it. :)

Got almost everything else bolted up and ready to go, just have to finish off the last min. bits over the weekend (finish relocating the battery and put the steering column back in hehe!).

Edited by platinum
Pretty much taking it down there next week anyway, with the instructions not to call me until its running because I'm sick of seeing it. :)

:lol: I remember saying the same thing to Shaun when dropping my car off to get it finished...

does the RB30 allow for use of the factory oil cooler from the RB25?

if you dont want to run it are there any things you need to do to allow the external coolers sandwich plate to bolt to the block without leaking?

so with the filter direct to the block i does have issues with the thread being too long?

havent pulled apart the std oil cooler to see if it runs its own separate thread for the filter or not.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
    • I started removing the tank a while back with the intent to give it a proper clean. Got to a bolt that I couldn't undo completely due to a diff being in the way, so just said f**k it and siphoned the gluggy old fuel out and called it a day. Looking it the tank it looks less corroded than the one in the pics for that billet hanger from Frenchy's anyway. Isn't it the fuel filters job to worry about this stuff? I scraped off most the crusty shit of the hanger but will give it another go before reinstall coz maybe the fuel and return pipes are also full of gunk  
    • Pretty sure it is a common fault. I believe this is the only part you need, but don't quote me as I don't have a V36.  I also believe it is a bit of a pain to change and the device needs to be encoded to the car once it is replaced, so may need someone with the right tools. Buy Genuine Nissan 48700JF00D (48700-JF00D) Lock Set-Steering. Prices, fast shipping, photos, weight - Amayama
×
×
  • Create New...