Jump to content
SAU Community

Recommended Posts

Does anyone know what you have to do to get wider wheels approved by the ACT RTA?

(Damn R32 with its 6.5 inch stockers)

Wanna go to about 8inches all round but want it road legal for insurance. The only decent japanese wheels start around that size it seems too.

Link to comment
https://www.sau.com.au/forums/topic/154957-wider-wheels/
Share on other sites

I had 8's with 235's all round on my 32, and the fronts were pretty out there so to speak. I couldn't lower the car at all. I'm not sure if that'd change heaps with a smaller tyre either.

I think they usually say 7.5's on the front.

Link to comment
https://www.sau.com.au/forums/topic/154957-wider-wheels/#findComment-2882979
Share on other sites

its the diameter that they pick on, no more then 2" larger then standard.

I find that so funny thou...coz in the ADR's it says nothing about a limit on diameter (except that the overall rolling diamteter must remain as close as possible) and it's all about width and track dependant on GVM

Link to comment
https://www.sau.com.au/forums/topic/154957-wider-wheels/#findComment-2883193
Share on other sites

I find that so funny thou...coz in the ADR's it says nothing about a limit on diameter (except that the overall rolling diamteter must remain as close as possible) and it's all about width and track dependant on GVM

Its Canberra.

Ignore the f**king ADR's. They don't care, and it will cause you no end of grief trying to get them past.

Just go and see an engineer, get it on paper and then shove it in their face.

I hate that goddamned scotman.

Link to comment
https://www.sau.com.au/forums/topic/154957-wider-wheels/#findComment-2886864
Share on other sites

Ok i've found a set of wheels that look allright...however I got told that i'll need some adaptor to fit them over the R32's front brakes.

I seem to dimly remember these adaptor plates (or whatever they are) not being legal? Does anyone know about them?

Link to comment
https://www.sau.com.au/forums/topic/154957-wider-wheels/#findComment-2887510
Share on other sites

I heard theyre legal as long as they dont stick out from under the wheel arch, its the diameter that they pick on, no more then 2" larger then standard.
Ive heard differently, when i enquired bout my Z. i was told that diameter wasnt an issue, as long as the width is no more than 1 inch wider than stock, you can go any size you want. hence why you see heaps of cars/SUV's with big ass chromes, but the width is still within range. This was approx 1 year ago, things may have changed. ..
Link to comment
https://www.sau.com.au/forums/topic/154957-wider-wheels/#findComment-2887648
Share on other sites

spacers. stay away, get wheels that fit without them, theyre unsafe and illegal. would you buy cothes that fitted as long you wore certain underwear? (remember youre a man not a chick)

Cheers for the advice, and the friendly reminder :(

Link to comment
https://www.sau.com.au/forums/topic/154957-wider-wheels/#findComment-2887823
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Started sifting thru my brakes to decide which ones I will run on Clem   Made me think I should just put them all on Silver...for when brake fade just isn't an option   Should be able to bump rotor up from 343x32 to 348x36 off Supra. Not sure if the Supra annulus is right for the Alcons or APs but trying g to find a used Supra\M4 rotor to test fit The Alcons seem to gain 1-2mm clearance which all helps  
    • So car is getting a few mods to the cage and some jacking points welded in Meantime Ol Silver gets a new gearbox and shiny clutch.  Old Box is being set aside for Clem  
    • Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
×
×
  • Create New...