Jump to content
SAU Community

Garrett Gt25/60r Turbos For Gtr (sold)

scotty_gtr
 Share

Recommended Posts

scotty_gtr Contributor

scotty_gtr

Posted
Posted (edited)

hey i got 2X garrett gt25/60R turbos (280-300hp ea)

they were on my GTR for 1500km untill i spun a bearing. so i had to replace the centres.

i want $1500 for them. Paid $2400 for them

Call me on 0412839851 or PM me.

they are also advertised with my GTR.

note: as above they are also advertised in my GTR thread. so technically they are advertised twice on SAU. dunno if there is a rule sayin thats not allowed. if anyone knows let me know.

cheers scott

Edited by scotty_gtr
Link to comment
https://www.sau.com.au/forums/topic/155488-garrett-gt2560r-turbos-for-gtr-sold/
Share on other sites
scotty_gtr Contributor

scotty_gtr

Posted
  • Author
Posted

just a quick edit. to cover myself. there are heaps of different variations of the 25/60r. to my knowledge mine are between 280-300 hp each. i think garrett made 280hp, 300hp, 320hp, 350hp and 400hp variations.

correct me if im wrong.

anyway they were good while my engine survived :)

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...