Jump to content
SAU Community

Help With Electrics?

One Three

By One Three,
in Four Door Family & Wagoneers

 Share

Recommended Posts

GoldZilla Grand Master

GoldZilla

Posted
Posted

Is your alternator alright? It should be sending roughly 14.4volts to your battery and electrical system to run everything. Also, there's usually a regulator on the alternator which kinda controls how much charge is going out from the alternator so as not to over-juice your car's electrical system. That could also be causing problems.

The third thing, there's another fuse box inside the car - pull out your coin tray on the RHS of the steering column, and there's a fuse box hidden behind that with a bunch of standard blade-style fuses there. i can't remember if there's any there which may sort out your problems, but it might be worth a check...

Silverback Community Regular

Silverback

Posted
Posted

Have had the exact same problem before. I cleaned the inside of the battery terminals with sandpaper to remove the hard crust that forms from the oxidisation at the terminal. That fixed it for a while, but then the problem resurfaced. I then pulled the other plug that sits on the positive terminal and gave everything a good go with the sandpaper. Hey presto, no more problems. I used to work at a battery fitting specialist earlier in life, and you would not believe how many people came in to us after spending hundreds on new alternators, electrical components etc. You could see that the battery would be in clean enough condition, but the hard surface that forms after a couple of years can stop the energy flow from the battery. Of course, when you checked it with a battery tester it would come up fine.

I'm not saying that there might not actually be something else wrong, but start the search for the problem at the source & you could potentially save a bit of cash..... and thats gotta be a good thing!

Stinky Rooster Grand Master

Stinky Rooster

Posted
Posted (edited)

Heres a helpful hint that I got from an auto sparky - if you have that green fuzzy looking gunge on the terminals, the very best way to get rid of it is boiling water. Just boil the kettle and splash some on before you take the terminals off and it will disappear like magic. :mellow:

Edited by newbie101

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...