Jump to content
SAU Community

Can't Boost In Hot Weather, Well Not The Usual Amount.

WogsRus

By WogsRus,
in Engines & Forced Induction

 Share

Recommended Posts

WogsRus Veteran

WogsRus

Posted
Posted

Hay guys, dam this hot weather, So dam hot it's not funny.

Anyway i have not been able to get higher then 12 psi on my stock turbo. Is this a heat issue? I have a FMIC, but 35 deg plus is ttoooo hot.

I readjusted the boost controller, but no good, can't get higher.

Is this a common problem. I have had no issues when cold, but today is the first hot day and hence my question.

kay33 Collaborator

kay33

Posted
Posted

[Hay guys, dam this hot weather, So dam hot it's not funny.

Anyway i have not been able to get higher then 12 psi on my stock turbo. Is this a heat issue? I have a FMIC, but 35 deg plus is ttoooo hot.

I readjusted the boost controller, but no good, can't get higher.

Is this a common problem. I have had no issues when cold, but today is the first hot day and hence my question.

reply

hey mate ive noticed in hot weather my car's turbo doesnt as well, but i think its because my pod filter is closed up, so i think the added heat makes it a problem, if u hav a pod try n get a heat shield that should fix the problem

MANWHORE Grand Master

MANWHORE

Posted
Posted

Hey

I'm sure that you know that the car won't run very well in the heat (you do live in the heat after all, lol). Mine runs liek crap.

But in answer to your question, nah, the heat won't stop you running high boost.

It's most likely the boost controller you're using.

Just to give you an example. If you disconnected the vacuum line from the waste gate actuator - so just leave it out in the air, and floored it, it'd probably hit 50 psi or something (don't try it or you'll blow the turbo and maybe your engine.

Ryanrb25 Grand Master

Ryanrb25

Posted
Posted

the stock turbo runs outta puff after 12psi anyways, i dont know why you'd wanna try put it up boost on a bloody hot day aswell...i can see alot of people shaking their heads right about now. you said your well aware of pinging etc and you say its fine, but most of the time you cant hear it pinging.

WogsRus Veteran

WogsRus

Posted
  • Author
Posted

she wasn't pining, well not till this morning, i added soem timming. Backed off REAL Quick.

This morning much cooler temps, but turbo still seams funny. I checked it and there is no shaft play, well no more then the specs say, all good there.

Going to check engine compresion to make sure.

I am using a gozzmo IBC. I am also going to put my 10 psi actuator back in, that seamed to work better.

I tell you what, these turbo cars make me VERY paranoid. Knock, ping, bang and so forht.

r33_racer Grand Master

r33_racer

Posted
Posted

hence why you leave things on the safe side especially in summer. Lowers the chances of it going Knock, ping, bang and so forth.

If you wanna go nuts with boost and timing in summer chuck a water/meth injection kit on it.

WogsRus Veteran

WogsRus

Posted
  • Author
Posted (edited)

Thanks mate, i am in the process of making up some FMIC cooler water kits, and possibly injection kits aswell. For now i just need to back of a bit. LOL

Also, how much differance does a heatrange change in a sparkplug make. I have BKR6EYA, but thinking of swapping to BKR7EYA.

The reason i want to do this, is that i have a Central 20 ecu, and has been tuned with safc to get correct air fuel ration and some timming knocked out, but i still get some ping, well i think anyway. So possibly going to a 7 hetrange plug could help a bit?

Edited by WogsRus
WogsRus Veteran

WogsRus

Posted
  • Author
Posted

Nothign wrong with it, simply put the stock one back in to get the EBC tuned to that, problem is that my wastgate still is stock and couses creep. The 10 psi gate is much better, so i will be switching to it.

It works much better with the 10 psi gate, it is just for tunning purpouses for the EBC.

Main problem since the weeknd, lack of boost over 10-12 psi, well not lack of but harder to get to that level of boost.

So i'm gona do some more research

r33_racer Grand Master

r33_racer

Posted
Posted

yeh a colder range plug will drop knock a little bit...but not alot. From memory from what cubes informed me ages ago it was equivalent to 1 degree of timing pulled out i think or something along those lines.

Kennedy Mentor

Kennedy

Posted
Posted

tune your ebc for cold AND hot. Does it have two settings? If so retune for both weather conditions as stuff like gain etc etc will be different for different temps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      Whoops!
×
×
  • Create New...