Jump to content
SAU Community

Recommended Posts

OK I've got a few sets of these left over from LED bulbs that I evaluated. They're great for parkers, not overly bright but do the job.

I've got 15 sets of electric blue, and 14 sets of HID white (pictured below)

parkers.jpg

Consisting of 2 x T10 LED globes for $10 delivered!!! Get in before the NS guys get onto them (their group buy apparently went tits-up!!!)

Brighter versions of both are available however, if you feel you need the extra oomph, they're $15 delivered and are also the same as offered in my dash kits due to the good spread of light they provide. (pictured below)

parkerdash.jpg

Link to comment
https://www.sau.com.au/forums/topic/157082-t10-led-parker-lights/
Share on other sites

lightcomp.jpg

I've had a few queries about the brightness of the dash type T10 over the standard type parker T10 with 3 LEDs

On the right is the 6 LED ($15 a pair), on the left is the 3 LED ($10 a pair)

I'm using the 3 LED type as I'm not that phased over the brightness, just that they match my Xenons.

Dan ill buy a set of what your running as i also need to match the HID's... The $10 ones look fine to me mate...

Can you bring a set to the dyno day and ill pay ya then and there... :P

  • 1 month later...
  • 2 months later...
  • 1 year later...

got mine today very happy with them they aren't too bright and that's just what i wanted! highly recommended. only downfall was i had to take my front bar off to get to the LH light to take that off, to put the led in since the water and fuse/battery box thingo was in the way.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...