Jump to content
SAU Community

Autosports "ultimate Control" Skidpan No#1, March 24th Oran Park


Recommended Posts

  • Replies 136
  • Created
  • Last Reply

Top Posters In This Topic

Sorry Corinne,

Not doing this day - car is going to cop an abusing over long weekend so I want to save it for that.

I'll most likely do the next day of this.

I dont think helmets are required for shid pan days, Its been so long since I did one though!

Jeff what rubber you planning to use?? Your goin to be all over the course with that stuff you got on there now

Edited by Risking

yeah i know :huh: thats half the plan, i havent got enough time to get organised. if i manage to change brake pads before the end of the week i'll be happy enough. unless your offering?

i am going to have to give up my spot because my car is not ready and i had to spend a few hundred $$ on it last weekend so it will put me out if i go..

i am going to have to give up my spot because my car is not ready and i had to spend a few hundred $$ on it last weekend so it will put me out if i go..

Thats fair enough..

We make Corrine Run... :(

Oh ha ha.. so not! Car needs some work..

So Corinne - what happens if we dont make the 40, do you know? The day will still run with a smaller field?

Im pretty sure we will just be running a smaller groups then.. It will still go ahead either way..




  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...