Jump to content
SAU Community

Car Wont Start R33 95' Gts-t Im A Noob To Skylines

jinkz

By jinkz,
in General Maintenance

 Share

Recommended Posts

jinkz Enthusiast

jinkz

Posted
Posted

as topic....car wont start it cranks over but sounds like no fuel...i checkd the fuel lines of the intake manidold and there wasnt any fuel coming outs wen i was crankin it...how do i check if its the fuel pump or if the filter is block?

things ive changed so far are sparkies and re set ecu and the radio is still workin...i havent change the filter or have any mods car is all stock

any help or idears would help or if any one can sms me on 0433194591 with some idears would be much apperciated... Left da 33' at my gf's work lol car wouldnt start at alll 2nght...wat an OD lol yeha well if any of u guys can help and yeah the at is in clayton and sleepin over at the gf work place need to pick it up in the morning cheers

jinkz Enthusiast

jinkz

Posted
  • Author
Posted

checkd the fuse and its ok which relay is it? and how do u check it?

Therefore fuel pump most likely isn't going

When you turn from ACC to IGN, (ON) can you hear the fuel pump whir for around 3 seconds?

Most likely a fuse somewhere, or relay.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...