Jump to content
SAU Community

Recommended Posts

My plans have changed and I am no longer going to be building a drag car so it's time for these parts to go to fund further upgrades for my car:

ITEM: 800hp+ RB26 HKS Twin GT2835 turbo kit; exhaust manifold, wastegates and rear turbo housings have been ceramic coated; comp housings have been polished. Also comes with dump pipes and polished stainless steel intake pipes and K&N filters.

This kit made 546rwhp@16psi on initial tune. Will make over 700rwhp very easily.

CONDITION: Very good used (~5,000km)

PRICE: now $4,500!

PICS: below

Item: GTR Trust/GReddy twin entry drag cooler 600 x 300 x 150mm with 2 x 60mm inlets and 100mm outlet

Condition: Excellent - as new.

Price: $1,800ono

To Fit: GT-R's or whatever you like

Location: Sydney

Contact: PM

Comments: No longer needed as I have changed my mind again and am upgrading.

ITEM: Apexi V-MAX SPL forged billet 2.6L crank

CONDITION: Excellent used

PRICE: $3,300

OTHER: Can be revved to 10K+ with the right head components; rated to 1000+HP.

ITEM: As new 05U RB26 block fitted with HKS 2.8L Step 2 stroker kit

CONDITION: excellent

PRICE: Cost $16K+ asking $9,000 or near offer

PICS: on request

ITEM: RB26 Apexi V-Max 270 deg 11.4mm camshafts.

CONDITION: Excellent - unused

PRICE: $900ono

ITEM: RB26 Apexi V-Max 9,000 rpm valve springs and retainers

CONDITION: Excellent - used for 1,000km.

PRICE: $700ono

Or Cams, springs, retainers for $1500ono

No timewasters or lowballers.

post-4183-1186352245_thumb.jpg

post-4183-1186352293_thumb.jpg

post-4183-1188639154_thumb.jpg

post-4183-1197616416_thumb.jpg

post-4183-1197616437_thumb.jpg

post-4183-1197616455_thumb.jpg

post-4183-1197616474_thumb.jpg

post-4183-1197616515_thumb.jpg

Edited by NXTIME
  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

All parts are "or near offer". If anyone is seriously interested in any of the parts, PM me :)

Edited by NXTIME
  • 2 weeks later...

Only if I have buyers for the rest of the kit. Would prefer to sell it all together.

Edited by NXTIME

Will consider selling Apexi crank and rods separately.

Also, added HKS Step 2 RB26 87mm 21mm pin pistons and rings set

  • 2 weeks later...

[

hey

just wondering about the 2.8 stroker kit???

is that a comlpete bottom end, pistons, bolts etc?

is it together or does it need assembling

very interested plz get back to me wen u can

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...