Jump to content
SAU Community

Recommended Posts

Hi all,

Up for sale is a set of R34GTT Standard Side Mirrors (complete) in QM1 colour. They are in excellent condition.

Price: $150

Contact: PM or email to stan[AT]2evolve.com.au

Reason for Sale: They're just lying around in my room...

Thanks

Stan

Hi all,

I have up for sale a complete set of R34GTT Standard Injectors (blue). They are in excellent condition and were in perfect working order when taken off my motor. Injectors have been stored in individual plastic + boxes (from SARD) since removal.

Price: $150.00 delivered via Express for all 6

Contact: PM or email to stan[AT]2evolve.com.au

Thanks

Stan

EDIT: NOT FOR SALE AT THE MOMENT

Hi all,

I have up for sale a standard R34GTT Fuel Filler Panel / Flap in QM1 colour. It is in excellent condition.

Price: $15 + Frieght

Contact: PM or stan{AT}2evolve.com.au

Thanks

Stan

Hi all,

I have up for sale a standard R34GTT Automatic Shifter Knob (black leather). It is in good condition and the reason for sale is because I now use the Nismo one from Momo.

Price is $30.00 delivered

Contact: PM or stan{at}2evolve.com.au

Thanks

Stan

Hi all,

I have for sale a R34GTT Standard Fuel Pump + Intake Sock. Taken off my car due to upgrades; in perfect working order.

Price: $50 delivered

Contact: stan{at}2evolve.com.au or PM

Thanks

Stan

Hi all,

I have for sale a R34GTT Steering Rack... purchased as a whole so I could take one of the arms off for a repair job. Rack is complete and in good nick.

Price: $150 (pickup prefered as it's quite hefty)

Contact: PM or stan{at}2evolve.com.au

Thanks

Stan

Hi

Up for sale is a standard set of R34GTT Caster Rods (pair). They are in good order and the reason they were removed was so they could be upgraded to adjustable items.

Price: $30 + freight (pickup preferred as they are quite heavy)

Contact: PM or stan{at}2evolve.com.au

Thanks

Stan

Hi all,

I have for sale a R34GTT BOV Cross Over Pipe; perfect for polishing or custom BOV fabrication. It's in excellent condition with no dents / gashes.

Price: $50 + Freight

Contact: PM or stan{at}2evolve.com.au

Thanks

Stan

hey Stan, on a side note, have you changed over the pipe that runs from the AFM to the turbo (the one that sucks shut if you run over 1 bar) .... I can't find these for sale anywhere ....

Hi all,

Up for sale is a set of R34GTT Standard Side Mirrors (complete) in QM1 colour. They are in excellent condition.

Price: $200

Contact: PM or email to stan[AT]2evolve.com.au

Reason for Sale: They're just lying around in my room...

Thanks

Stan

Hey Stan,

Are these off your 2 door or a 4 door? Is there any difference do you know cause my left mirror motor not the actual mirror but the one which controls when the whole mirror thingy moves in closer to the car when you press the recline button is stuffed.

1) No airbox available anymore - Nightcrawler; if you can help this guy out please do so :unsure:

2) Lanky; the mirrors are off my 2door and I'm 99% sure that there is no difference between the 2/4 door mirrors. Since you are in Epping you are more than welcome to come see them for yourself :P

Blue injectors are standard on the R34GTT - you should inform them of this.

I managed to pull 210rwkw before they maxed out; others have managed to pull more from them. Regardless; if you're chasing big power then you need bigger.

Nonetheless; these ones are NOT for sale anymore.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...