Jump to content
SAU Community

Recommended Posts

Hi all, time has come to part with these wheels as I'm going for 10.5 wide!!!

- They are in absolutely perfect condition bar a tiny little gutter rash on one wheel which is more on the rolled lip/edge so is barely visible at all.

- 18 x 9 +22 designed specifically for R32 GT-R.

- Come with Dunlop Direzza 02G Semi Slicks, 235/40/18 with 75-80% tread left!!! ($1600+ tyres alone).

Asking $3800 FIRM. Pick-up available from Eastern Suburbs Maroubra, Rockdale or Padstow. Will ship with courier service at buyers expense.

Some pics:

DSCN7873.jpg

DSCN7884.jpg

nismo1.jpg

side.jpg

SERVER IS DOWN - Check Flickr account for some pics:

http://www.flickr.com/photos/justinfox/set...57594556972441/

Edited by justinfox
Link to comment
https://www.sau.com.au/forums/topic/160635-fsl-syd-nismo-lm-gt4-18x922/
Share on other sites

OK more detailed pics taken TODAY.

Car is at paintshop, lots of dust on the ground which helps to show off the tread! :happy: Also pics of the gutter rash.

1.jpg

2.jpg

3.jpg

4.jpg

5.jpg

damage.jpg

Shot of the rash.

damage2.jpg

Another shot of the same rash.

ALL OTHER WHEELS ARE IN ABSOLUTELY PERFECT MINT 100% CONDITION.

Edited by justinfox

Very tempting...

Bit of a newbie question, I know it says designed specifically for an R32 GT-R, but do you need to run them with spacers etc? I have coilovers on the car too fwiw.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...