Jump to content
SAU Community

Recommended Posts

hey guys. just wanted to know what to set my knock sensor to.,

uras, or whover.

how do i set it up.

atm the jumper for it is set to 1-2. and in parameters im using the air intake temp/knock sensor 2 with it set to resonate and 7.02.

is this cool??

non res and around 7khz works well.

  • Replies 765
  • Created
  • Last Reply

Top Posters In This Topic

Trent, how would you diagnose knock with EMU? As long as its above 1% its all knock ? I forgot what knock is there in. % or not.

How far would you usually go with tuning ? Under 30, under 10 or fight knock until its below 0 threshold ?

Thanks!

ok i have finished my car and my mechanic tells me that i need to get it tuned.

WHERE THE F#%K CAN I GET IT TUNED IN BRISSIE AND GOLDY AREA for a good price???

Try Godzilla - I hear he does very good work!!

^^ yeah but ive never had issues unless its wired wrong. try updating EMU and software from the greddy japan site.

Thanks for the reply. The wiring looks ok (to me), the car runs ok, but the error log and flashing red light on the EMU continues. My software on the laptop is v2.16, I'll check what is loaded on the EMU when connected, but I think it's up to date.

I'll PM you a config printout (pdf), if you wouldn't mind having a quick look.

cheers.

Trent, how would you diagnose knock with EMU? As long as its above 1% its all knock ? I forgot what knock is there in. % or not.

How far would you usually go with tuning ? Under 30, under 10 or fight knock until its below 0 threshold ?

Thanks!

i always use my GIZZMO K-Mon to monitor knock as a back up but the EMU shows actual knock if you get any spike at all it is generally knock.

thanks very much pear...would they be in yellow pages?

any contact info?

they the ones on ashmore rd or ingelston rd?

http://www.godzillamotorsport.com/

addr and contact details are on their site. -- ingelston Rd

I haven't been there myself, but have heard good comments from other SAUQld members.

ask for Mark -- or send him a pm 'markr34gtr' http://www.skylinesaustralia.com/forums/m4681.html

good luck, & keep us posted!!

Pear

Check that the signals going from the ignition relate to the right ones coming out

mine threw up that error and a red light when the channels didnt match to the igniter no. (3,4&5 were not matched up properly)

I changed them and the error messages went away

Hi Haines, thanks for the reply.

I've had another look at the wiring, visual inspection only, but it looks ok.

Next step is to get it tested.

I've attached pics of wiring and EMU setup. If anyone what to comment, please feel free

Cheers

Pic___Ign_Wiring01pdf.pdf

ScreenShots_of_Setup01.pdf

Hey guys, sorry to ask this one as I dont know if its been covered (dont have time to read 26 pages!).

The software that can be bought for the Emanage, Nengun says its in japanese, Is that just the instructions or is the program in japanesE?

Haha! I got the N-4 harness. Nice little piece of plastic ))

Swapped Ne and G, then Disconnected A and Ar1 hooked them up with other 2 free connectors.

Now I got no Water temp. Will be a bitch to find out which one is water temp now.

Btw, from factory N-4 harness comes wired with 2 knock sensors or air inlet temp and water temp ?

Thanks !

Ok. Swapping Ne/G was a bad Idea !!! I put them back, like greddy default and got my timing control/datalog back. Before it was 111deg. everywhere.

I did a few power runs like that and got massive missfire in 160km/h area.

The knock sensor 1/water temp should be left along, like greddy n-4. It will read water temp, not knock. And remove intake air temp and swap it with another purple/yellow wire. And u will get knock 2 working.

Now the funny part.

RB20DET inj. pin out order is a bit different to rb25/rb26 !

RB26 goes like #5 #6 #4, and rb20det goes like #5 #4 #6. I just figured that out. And now, its 3.30 am and I'm thinking how to swap those wires. Any good ideas ?

Other issues I've discovered. Need to adjust the TPS in EMU. Otherwise u won't have good idle and idle afr/s and no map trace.

Consult came up with TPS error when I didn't calibrate the TPS in EMU. After calibration this error went away.

Before swapping Ne/G back to the greddy default order G/Ne. (Not Ne/G), EMU was attacking me with ign. channel errors. all 6 of them.

Now I got no Errors in EMU.

But I still got the 21/ign. circuit error in ecu through consult.

Haven't got a chance to take a car for a datalog run after that.

Can post some datalogs of what was it like before.

I'm really having a hard time with making an EMU work )) Why me ? )))) lol.

I thought n-4 harness with magically solve all my problems. But it damn didn't do it right away or yet. hehe.

Hope for some input here.

hi there i wonder if anyone can tell me where i am going wrong gor r33 gtst 1995 i have wirried emu but i keep getting these error shortly after car is running

30:0441-0005[incorrect 1CH ignition input signal]

31:0442-0004[incorrect 2CH ignition input signal]

32:0443-0006[incorrect 3CH ignition input signal]

33:0444-0001[incorrect 4CH ignition input signal]

34:0445-0003[incorrect 5CH ignition input signal]

35:0446-0002[incorrect 6CH ignition input signal]

ii have checked wirring and is ok i have swaped jumpers over but still get the same fault do i ahve to set jumper to 12v or 5 volt for this car

would greatly apreciate it

hi there i wonder if anyone can tell me where i am going wrong gor r33 gtst 1995 i have wirried emu but i keep getting these error shortly after car is running

30:0441-0005[incorrect 1CH ignition input signal]

31:0442-0004[incorrect 2CH ignition input signal]

32:0443-0006[incorrect 3CH ignition input signal]

33:0444-0001[incorrect 4CH ignition input signal]

34:0445-0003[incorrect 5CH ignition input signal]

35:0446-0002[incorrect 6CH ignition input signal]

ii have checked wirring and is ok i have swaped jumpers over but still get the same fault do i ahve to set jumper to 12v or 5 volt for this car

would greatly apreciate it

ok i sorted that error out but what voltage do i run 12 or 5

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...