Jump to content
SAU Community

What The ? My Clutch Is Hissing @ Me

itbmils
 Share

Recommended Posts

itbmils Proficient

itbmils

Posted
Posted

OK pps

I have an R32 GTR - with near new excedy h/d clutch kit installed. It's been installed for about 5-6000 klms or so and it's been fine.

BUT

In the last week or so - I've been getting in intermittent hissing noise from inside the car ??

At first I thought it was coming from the air con – but even when it's off – I can still get the hissing

I've done some investigation - and I think it's coming from the clutch (peddle)

stop that laughing – I don't do drugs (any more :))

Form time to time (maybe once per day) - I can feel the clutch peddle go slightly heavy and then when I press the peddle I get a hissing sound coming from the foot well.

I can not hear it from outside the car (not a bearing) - and it's sounds like a air / vacuum leak coming from somewhere under the dash.

When it's doing it, I can literally just touch the peddle on and off (not actually engaging the clutch) and I will hear the noise. It will also keep hissing all the way through the travel of the peddle (all the way in and out) - told you it was not a bearing :D

then it just stops – and the peddle feel returns to normal

talk to me - am I hearing things ?

Link to comment
https://www.sau.com.au/forums/topic/161478-what-the-my-clutch-is-hissing-me/
Share on other sites
ceedub Community Regular

ceedub

Posted
Posted
I believe GTR's run a vac booster for the clutch. Much like all the new nissan 4wd's do.

I'd say its stuffed. :)

Yep, I got the same problem. Been like that for a few months now. Haven't gotten round to fixing it. Not sure what long term effects it may cause - i've been assured there are none.

The GTR has a vacuum booster on the clutch. To temporarily stop the hissing you could disconnect the vaccum line that goes into the clutch booster and plug it - however your clutch pedal will become 3 times harder to engage.

To fix you need to replace vaccum booster.

Cubes Grand Master

Cubes

Posted
Posted

Might be worth checking out a navara or something as the booster may be similiar and bolt up without too much trouble.

Wonder what Nissan would want new for a gtr item.... :S

Second hand + a heavy duty clutch its just a matter of when it does it again. Being 10-15yr old and all. :(

Does any one have pics of the booster? Its been some time since I've seen one and able to run out and check the Navara. Funny enough a few things on the navara are the same as the R32. :) The door latch mounted on the door frame is one that comes to mind. :(

  • 1 month later...
GTRNUR Grand Master

GTRNUR

Posted
Posted

Awakening a dead thread...

Got this problem with my R33 clutch booster as well.

THe booster is located in the engine bay inbetween the firewall and clutch MC.

There is long term repercussions for not fixiing it. The nylon bushing in the clutch pedal will crush and wear out, then the pin will run directly on the pedal and wear the bushing hole and damage the pin.

I fixed my bushing issue by machining a brass one up, then found this thread which explains why its happened in the first place!

Cheers,

Ian

Burgerman Enthusiast

Burgerman

Posted
Posted

I have an R32 GTR and it had the exact same problem. It was making a hissing noise when you push in the clutch. I got it fixed sometime last year and it's not a big thing. I think the part cost $120 or so and was charged maybe $60 for labour? Once it was done the pedal was lighter to push down on and I guess if it's vacuum assisted you know when it's really stuffed when you have to push alot harder to get it working.

I would say most mechanics in brissy can replace it fairly easy for you I got it done at a local mechanic no problems.

GL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • MBS206
      NC MX5

      By MBS206 · Posted

      Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
×
×
  • Create New...