Jump to content
SAU Community

Recommended Posts

I have recently rebuilt my '96 R33 GTS-t, replacing the turbo and many other parts. The following are whats been left over either not required or replaced as explained. Prefer not to ship the turbo or dump pipe if at all possible. I am located in Melbourne.

ARC - Airbox

- As above, suits a ECR33, was used for around a year

- Has ARC label and suits the standard turbo or the GT-RS above. The GT2835 has a different outlet so no longer fits.

- As per Nengun - ARC Airbox

- $250

Defi - Exhaust Temperature Gauge

- Not required, had plenty of other gauges

- The Defi control box is required to operate, but comes with sensor etc.

- This is not a BF but a normal Defi Link - Gauge

- $180

--

Nismo Low Temp Thermostat

- Not needed, brand new never installed

- As per Nengun - Nismo Thermostat

- $50

SOLD PENDING PAYMENT

Catco - High flow cat

- Highest flowing cat available, brand new, never installed

- As purchased from batmbl on the forums - BOS Importing

- $320

SOLD

CES - Split Front/Dump Pipe

- Purchased from CES in Queensland for around $600 (should be able to find receipt)

- Was purchased as the stainless steel with ceramic coating model

- Attachment has been inserted by mechanic for tuning/etc.

- Splitter flange for the turbo has been removed to suit the GT-RS turbo (which already has this)

- Some scrapes on the bottom, can take more photos if required

- $200

SOLD

HKS GT-RS turbo + short parts

- Was replaced with a HKS GT2835 after rebuild

- Original installation problem damaged core which was replaced by Racepace (receipt available) at a cost of ~ $1000 less than 10,000km ago

- Brand new HKS lines/connectors (from the new GT2835)

- Original HKS J Pipe

- Purchased at Nengun - GT-RS May 2005 for $2600

- $1800 - Will now do $1700 + post

SOLD

Blitz - SBC Dual Solenoid Boost Controller

- Among the best available boost controller with dual solenoid

- Brand new, ended up not needing it

- As available on Nengun - Blitz SBC

- $420

SOLD

Greddy Radiator Breather Tank

- Not needed, brand new never installed

- 8mm as available on Nengun - Greddy Breather Tank

- $120

SOLD

Greddy water temp gauge adapter

- not needed, brand new never installed

- As per Nengun - Water adapter

- $20

SOLD

Nismo - Fuel Pressure Regulator

- Not needed, brand new never installed but no longer have box

- As per Nengun - FPR

- $120

SOLD

Greddy - Catchcan

- Used, comes with hoses to fit ECR33 breather lines, no longer needed

- Fairly good condition, genuine Greddy as purchased from Nengun

- $90

SOLD

XTR - Turbo Bag

- Rough condition, should still work fine

- $50

SOLD

post-4758-1175321000.jpg

post-4758-1175321012.jpg

post-4758-1175321020.jpg

post-4758-1175321027.jpg

post-4758-1175321034.jpg

post-4758-1175321044.jpg

post-4758-1175321050.jpg

post-4758-1175321056.jpg

post-4758-1175321062.jpg

post-4758-1175321069.jpg

post-4758-1175321077.jpg

post-4758-1175321094.jpg

post-4758-1175321101.jpg

post-4758-1175321110.jpg

Edited by halz

Greddy Radiator Breather Tank

- Not needed, brand new never installed

- 8mm as available on Nengun - Greddy Breather Tank

- $120

Greddy - Catchcan

- Used, comes with hoses to fit ECR33 breather lines, no longer needed

- Fairly good condition, genuine Greddy as purchased from Nengun

- $90

ill take these two thanks im on the gold coast tried to pm not shore if it has worked

I'm keen on the Defi Exhaust Temp Gauge, assuming it's the DF-02406.

Will check my finances in the next few days and let you know via PM...

I'm keen on the Defi Exhaust Temp Gauge, assuming it's the DF-02406.

Will check my finances in the next few days and let you know via PM...

Updated some items and yes the gauge model is: DF02406.

Greddy Radiator Breather Tank

- Not needed, brand new never installed

- 8mm as available on Nengun - Greddy Breather Tank

- $120

Greddy - Catchcan

- Used, comes with hoses to fit ECR33 breather lines, no longer needed

- Fairly good condition, genuine Greddy as purchased from Nengun

- $90

ill take these two thanks im on the gold coast tried to pm not shore if it has worked

payment sent thanks

Halz, does the turbo come with everything it came with brand new? Would be a straight bolt on no fuss on an RB25 as HKS intended right? Still contains the HKS actuator etc.?

do you know how much the turbos are good for?(power figure)

I was making a solid 240rwkw tuned by Racepace. Originally when it was not installed correctly and the ball bearing catridge had broken. Racepace replaced this no more than 5,000km on the new catridge. It spins freely and has pratically no play in it.

But as it turns out, I had a broken ringland in #6 and ended up having to get a complete engine rebuild where I opted for a larger GT2835 which is making 270rwkw.

Halz, does the turbo come with everything it came with brand new? Would be a straight bolt on no fuss on an RB25 as HKS intended right? Still contains the HKS actuator etc.?

Yep, comes with everything that was included as from HKS. The oil water lines from the GT-RS was re-used on my new turbo, so the oil/water lines as the brand new ones from the GT2835 (identical). Also includes the J pipe.

Install should be pretty simple, suits the standard manifold (which I still run) and I had the dump/front pipe as for sale above -- uses the standard exhaust flange.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
×
×
  • Create New...