Jump to content
SAU Community

What Do You Think Of This? Im Looking To Buy One

T88turbo
 Share

Recommended Posts

jake33 Experienced

jake33

Posted
Posted (edited)
but thats not manual.

ha yeah i realise... its an auto with tiptronic.

overall there pretty nice. not too many of them around. they look good stock or dumped with a kit and wheels... nothing too over the top IMO

Output ranges from 240 hp to 301 hp (179 to 221 kW) and 246 lb·f to 287 lb·f (334 to 390 Nm). found on the web

Edited by jake33
Skyline_95GTS Enthusiast

Skyline_95GTS

Posted
Posted

Tiptronic has nothing on manual - might as well leave it in auto...?

Test drive it and see what the power is like... im curious to know what these things go like - looks nice

T88turbo Collaborator

T88turbo

Posted
  • Author
Posted

I went to see the one for $35, 500 bluddy good looking car better than what it looks in the picture. The thing i like about them is the front they look like a porsche. The lights on either side are pumped up.

I drove it they got some power the whole front launches when you give it. I wonder how they would sound with an exhaust, it sounded nice without one.

Al-R33 Enthusiast

Al-R33

Posted
Posted
I went to see the one for $35, 500 bluddy good looking car better than what it looks in the picture. The thing i like about them is the front they look like a porsche. The lights on either side are pumped up.

I drove it they got some power the whole front launches when you give it. I wonder how they would sound with an exhaust, it sounded nice without one.

Always liked the sound of

leetom Proficient

leetom

Posted
Posted

i've been checking them out for awhile now & the more i look the more i like,they look schmick with a good body kit.

they also seem to be getting a bit cheaper to, 2003 on j-spec $29300,2004 $38600 2006 $49700,...yeh i'll have one... a black one.

scathing Grand Master

scathing

Posted
Posted
nice, but id definately get a 350z over one, in essence the same car but the Z is sportier, not a luxo cruiser

The 350Z is lighter, is more likely to have Brembos, the handling is more direct, and the chassis is stronger (more bracing and spot welded). As a sports car, it does a better job.

However, sometimes having only 2 seats is a right pain in the pass. And the front seats in the V35 are heaps nicer. Its also a bit more isolated in terms of ride and sound dampening, which makes it great as a cruiser.

Most of the mods between the 350Z and V35 are interchangable (the only thing that isn't is the exhaust, given the extra length of the V35). Since these cars are getting very popular among the tuner set overseas (especially in Japan and the USA) you can get more power if you want.

I've been giving some serious thought to trading in my car and getting a V35 coupe. I'll see if I'm still as enthused about track work a few months down the track, or if I'm in more desperate need for rear seats.

WRRR Rising Star

WRRR

Posted
Posted

FWIW

Looked at and drove a premium 6 speed manual version with the "handling kit" and Brembo's. Silver, low km, sat nav, leather, blah blah ...

Nice car, looks great, handles pretty well (for an allrounder type setup), not as much room inside as you would think and does not go anywhere near as hard as it looks in standard form (although I believe a few mods and they go much better - ie look at some of the TT kits from the US)

Decided to pass on it and ended up buying a GTR.

Nuff said.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...