Jump to content
SAU Community

Recommended Posts

Hey all,

I did a search but couldn't find anything on this topic. Just wondering what mods should be done to a stock RB26 to get the most out of it.

ie. 1. Air induction kit

2. ECU

etc.

I don't know to much about the RB26 engines so I just want to know what people usually to these and how the get them going so fast.(I just imported a purple R33 GTR v-spec pics soon)

Cheers

Link to comment
https://www.sau.com.au/forums/topic/163113-rb26-mods/
Share on other sites

What you got to spend?

how far do you want to go?

what can you afford?

you need to think about all of these! you've got to remember that you have a car thats going to cost a bit to maintain.

Edited by Angus Smart
Link to comment
https://www.sau.com.au/forums/topic/163113-rb26-mods/#findComment-3027287
Share on other sites

Try the basics first

Hi flow air filter - cheap

Irridum sparkplugs - moderate price

cam gears - slightly pricy

Power FC computer and tune - pricy

new turbo's - very pricy

Convert RB30 - Very pricy

Other go fast things

Full exhaust - Very pricy

High quality tyres - Very pricy

Use search, there's no end of upgrades.

Link to comment
https://www.sau.com.au/forums/topic/163113-rb26-mods/#findComment-3027511
Share on other sites

Hey guys,

Things have been changed a bit, the importer lied to me and said that he got a purple GTR v-spec but I called him yesturday and he couldn't find one(bullsh!t). Anyway I was only going for the R33 because I love that purple colour, but now I can't get it so I am going for a silver R32 GTR with a bit of work done(290 awkw's).

What sort of 1/4 times would we be looking at with this much power?

I want one good run out of it and then I will drop the boost for a daily driver.

Link to comment
https://www.sau.com.au/forums/topic/163113-rb26-mods/#findComment-3027672
Share on other sites

Here is all the info, ley me know what times you guys think it should run.

Apexi power fc

Apexi AVCR

Apexi twin pod filters

Apexi 3" N1 stainless steel exhaust

Nismo injectors

Nismo dump pipes

HKS gt 25/30 turbo's

HKS adjustable coilover suspension fuel regulator

290 awkw

Cheers

Link to comment
https://www.sau.com.au/forums/topic/163113-rb26-mods/#findComment-3042339
Share on other sites

Here is all the info, ley me know what times you guys think it should run.

Apexi power fc

Apexi AVCR

Apexi twin pod filters

Apexi 3" N1 stainless steel exhaust

Nismo injectors

Nismo dump pipes

HKS gt 25/30 turbo's

HKS adjustable coilover suspension fuel regulator

290 awkw

Cheers

290kw At wheel consider no internal done...you will be expecting mid 11s Quarter mile and depend how drive. Hope you have good tires and clutch!!! Run it and lets us know =) Good lUck!!

Link to comment
https://www.sau.com.au/forums/topic/163113-rb26-mods/#findComment-3045957
Share on other sites

Yeah its got a twin plate and 10inch tyres all around. What do you guys think I need to do to get a 10 out of her?

I know I need some bigger AFM's Z32 probly (has anyone got any for sale or know where I can get them) and and maybe a bigger cooler.

What else?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/163113-rb26-mods/#findComment-3046706
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...