Jump to content
SAU Community

Recommended Posts

G'day guys, i own a ca18det 180sx.

i need more ideas of how to fix this problem, basically car won't stay running without my foot on the accelerator, and when i do it won't rev pass 900.

i've changed the spark plugs, test the coils, did a compression test (all good), cleaned the most of the adaptors.....

is there anything else i should do to to get this car on the road again?

Link to comment
https://www.sau.com.au/forums/topic/163986-car-wont-rev-help/
Share on other sites

not wanting to sound rude but what could be wrong with the afm? i did took the thing off and gave it a quick cleaned, and from inspection,i thought the thing doesn't have too much mechanical components nor electrical components for it to be related to any problem.

as for the intercooler, while carbie cleaning the throttle body, i did took some of the IC pipes off to clean off some of the oil, i remember i did tighting up all the clamps but will pull it apart and pull it back together again tomorrow.

uummm at this point i gonna say no to a new comp :) wallet is quiet empty now after easter.

by any chance could be related to the crank sensor?, cos i got it replace a few days before this rev problem

This happen a day after i degreaser the engine, but i did took the car out after i cleaned it, and it was fine

Edited by dOOb
Check your intake piping, I popped off a pipe today and it did exactly as you described it. Won't rev and dies if you lift the foot off the accelerator.

took all the pipes of today and put it back today nothing change so................

Is the CAS tight?

It might not be on tight enough and the timing is way out.

Check your connections on EVERYTHING electrical too. Just unplug them, and plug em back in.

........i messed around with the crank sensor, i didn't take it off just losen the bolts and turned it in both directions a lil bit at a time. NOW THE DAME THING DOESN'T EVEN KICK OVER.

CAS was tight, timing is okay after i changed the crank sensor, i've already unplugged most of the adaptors and cleaned it with carbie cleaner.

ANYBODY GOT ANYMORE IDEAS?

Edited by dOOb
try a fuel pump. i replaced one in a r33 that was doing the same thing fixed the prob

i checked the fuel pump when i changed the "O ring" on top of the fuel tank about 6 weeks ago, fuel pump looks to be near new, also checked the fuel pressure and thats okay aswell.

thanks for that tip SXC_R33, can anybody think of anything else that is causing this problem?

+1 afm is stuffed actually a really common failing part and it wuold make the car not run past about 900rpm but you should be able to start the car fine, try starting the car with it unplugged if its worse its probably ok but if its the same then it could be stuffed

its entirely possible that its the AFM as stated, and because its been running rich for so long you have simply fouled the plugs...

i'd say get a new set of plugs ($20 all up for NGK copper BCPR6ES) and get a hold of someone's AFM

change them both at the same time and see if it kicks over and runs ok

hope that helps

+1 afm is stuffed actually a really common failing part and it wuold make the car not run past about 900rpm but you should be able to start the car fine, try starting the car with it unplugged if its worse its probably ok but if its the same then it could be stuffed

seeing how i've stuffed around with almost everything i can think of, next will be the AFM, will try it unplugged or swap it with a mate.

its entirely possible that its the AFM as stated, and because its been running rich for so long you have simply fouled the plugs...

i'd say get a new set of plugs ($20 all up for NGK copper BCPR6ES) and get a hold of someone's AFM

change them both at the same time and see if it kicks over and runs ok

hope that helps

i've already changed the plugs when this problem first occured, but that didn't much to it but might changed to those recommended to see if theres any different.

yeah but what i'm saying is that the AFM is the cause, and the plugs are fouled because of the AFM

so a new AFM might fix the cause, but the car might not start still because the plugs are foulled

you have to fix the cause (AFM) and the effected parts (plugs) at the same time to see if this is in fact the case

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...