Jump to content
SAU Community

Recommended Posts

and in a straight line (with good mods), Autos will beat Manuals...

if the manual has the same mods the manual will still win, unless you are talking 10 second cars, or the manual driver keeps missing gears. manaul gearboxes are lighter, you can change faster and at the rpm you want it to change at. if you are talking BIG power cars then an auto can be the way to go.

the best way to launch an auto is, as people have said, left foot on brake, right foot on gas, bring revs up till the car is about to start wheelspinning. if you are coordinated enough you can use the hand brake too. this will add more braking power onto the rear wheels.

using the handbrake is a good way to load up a manual car too. doesn't do the clutch much good though.

thanks guys. been meaning to ask this question but keep forgetting that i wanna know. is it possible to do a standstill burnout in an auto as well?

i skipped most of the replys so its poserbly all ready being said. but yes you can do a burnout in an auto and it is easer then a manual.

just bring the car to a stand still. step on the brake bring the revs up release the brake a smudge, (this locks up the front brakes) keep incressing revs and you should have the rear wheels burning. then just controll how much power you give it and how much brake you wont (to controll how fast the car moves)

This is being a little mean but i had these conversations with friends in i think Grade 4 when i was learning my 7 & 8's times tables.. but not up

to my 9's as yet.. they were a little hard at that time...

But anyway, straight out unless ur car is making 200rwkws and u have 3:9's or higher gears ratios in the diff auto sucks and manual is much more fun..

People who say auto is faster etc etc, can eat an overdue banana. Manual delivers power in a completely different way, more power goes

to the wheels with a manual gearbox as to an auto in ANY car..

As said earlier in this topic, autos are only quicker when cars are running 10 second passes and u need more traction, manuals are full of

wheelspin when ur popping the clutch and smashing through gears because of the way the power is being delivered to the wheels..

I had an auto Passage with 110rwkws and no matter how hard i stalled up the auto off the line a manual sigma would keep up untill atleast 40kms.. lol

Edited by Dean_HR31

Auto Trans rebuilds are too expensive, its LOTS cheaper to purchase a 2nd hand one as they are being sold for a couple of hundred bucks. I picked up a second hand one for 2 cartons of beer that I saw come off a car and the only reason it was changed was for a manual conversion. I will be slowly upgrading the trans to have a manual shift kit, hi-stall and new bands ect.... So that when mine goes bang, it will be easy to swap over. But for now I have a bigger trans cooler and I also service it every 10k, so I am not expecting it to break any time soon.

Chris

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...