Jump to content
SAU Community

Recommended Posts

and in a straight line (with good mods), Autos will beat Manuals...

if the manual has the same mods the manual will still win, unless you are talking 10 second cars, or the manual driver keeps missing gears. manaul gearboxes are lighter, you can change faster and at the rpm you want it to change at. if you are talking BIG power cars then an auto can be the way to go.

the best way to launch an auto is, as people have said, left foot on brake, right foot on gas, bring revs up till the car is about to start wheelspinning. if you are coordinated enough you can use the hand brake too. this will add more braking power onto the rear wheels.

using the handbrake is a good way to load up a manual car too. doesn't do the clutch much good though.

thanks guys. been meaning to ask this question but keep forgetting that i wanna know. is it possible to do a standstill burnout in an auto as well?

i skipped most of the replys so its poserbly all ready being said. but yes you can do a burnout in an auto and it is easer then a manual.

just bring the car to a stand still. step on the brake bring the revs up release the brake a smudge, (this locks up the front brakes) keep incressing revs and you should have the rear wheels burning. then just controll how much power you give it and how much brake you wont (to controll how fast the car moves)

This is being a little mean but i had these conversations with friends in i think Grade 4 when i was learning my 7 & 8's times tables.. but not up

to my 9's as yet.. they were a little hard at that time...

But anyway, straight out unless ur car is making 200rwkws and u have 3:9's or higher gears ratios in the diff auto sucks and manual is much more fun..

People who say auto is faster etc etc, can eat an overdue banana. Manual delivers power in a completely different way, more power goes

to the wheels with a manual gearbox as to an auto in ANY car..

As said earlier in this topic, autos are only quicker when cars are running 10 second passes and u need more traction, manuals are full of

wheelspin when ur popping the clutch and smashing through gears because of the way the power is being delivered to the wheels..

I had an auto Passage with 110rwkws and no matter how hard i stalled up the auto off the line a manual sigma would keep up untill atleast 40kms.. lol

Edited by Dean_HR31

Auto Trans rebuilds are too expensive, its LOTS cheaper to purchase a 2nd hand one as they are being sold for a couple of hundred bucks. I picked up a second hand one for 2 cartons of beer that I saw come off a car and the only reason it was changed was for a manual conversion. I will be slowly upgrading the trans to have a manual shift kit, hi-stall and new bands ect.... So that when mine goes bang, it will be easy to swap over. But for now I have a bigger trans cooler and I also service it every 10k, so I am not expecting it to break any time soon.

Chris

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...