Jump to content
SAU Community

Recommended Posts

Hey guys/girls

I require any input that you guys/girls can offer me.

Vehicle details:

r32 gts4-t

manual

turbosmart boost controller (Boost Tee)

3inch exhaust

FMIC

stock turbo

12 psi

dump pile

2 x BOV - i. after market - ii. stock (Weird previous onwer)

I have recently converted my r32 gts40t from auto to man (this was performed at GT auto garage) with a new exedy clutch and gt-r gearbox and after a good work out..... my baby started heistating 4000 rpm so as i have read on the forums here at the SAU website it could be hair crack in the coilpacks.

SO I gluing them with arodite and performed a compression test and in the process smashed the ignitor loom plugs (where it plugs into the coilpack) so i got a second hand loom from STZ automative.

Got back home put the new loom in and what do u know misfire on idle and load. After as for a mates help (he has a r31 with a rb20det) we swapped the ignitors than tried the loom. Ignitor didn't help. Loom resulted in no misfire at idle so we jumped in and went for a spin..... on load stall. So i thought maybe sparks / coilpacks........... Got new SP coilpacks, NGK iridium spark plugs, regap.

So after inspecting the loom that i got from STZ i found that the guy had given me a rb26 loom. So i returned it. Got a second rb20det loom and changed fuel filter.

Decided to send the car to GT auto garage car didn't mis for them heistated still. I asked for a new walbro pump to be installed, plugs to be regapped, SP coils to be installed.... 50 metres down the road STALL at 40 kms..... steering heavy "battery light comes up" could it be an alternator (&%*$ dying?

Currently heistating over 5000 rpm and stalling randomly and running RIch.

Well any help would be AWESOME

I have tried:

1. New plugs

2. swapped loom, ignitor for another rb20det

3. cleaned and resolder AFM pins

4. New SP coilpacks

5. New fuel filter

6. New fuel pump

7. checked for splits in Intercooler piling

Possbility i have thought of or read from the forum:

1. plastic from the plug has fallen into a cynlinder during compression test

2. alternator is F*&ked - i will find a friend with a multi meter

3. CAS

4. ACC

5. ECU in limp mode

Help........... would be awesome or even ways to test what it could be

I might even just RIPP THE 20 out and put in a 25 or 26 when i can afford it :P

Edited by RipNGrip

Update: Haha i will reply to myself! :closedeyes:

AFM soldered and cleaned

cleaned TPS plug

checked for leaks

occasional missing on idle! Revs fairly freely and doesn't stall on release (drops to low revs)

Intermittently stall? (not completely sure - battery light comes on engine sounds like it cuts and battery light goes off) but i charged the battery (battery less than 12 months old) today and tightened some of the connections

i'm not too sure if youve done it already? aac valve. my rb20 would stall at every bloody intersection and traffic lights

that i possibly stopped at and towards the end even when i slowed down to minimal revs.

i cleaned mine and it was like a totally new car. also adjusted the idles and its a dream

also when my afm went i couldn't get any power over about 3 grand. every time i took it to mechanics it ran fine.

theyre my experiences with similar problems under any sort of load.

hopefulyy it helps somewhat.

Hey mate have u actually tried using a different afm altogether? i have the same problem as you i resoldered my afm and it only temporarily fixed the prob i tried using a diff one and problem solved.

Hope that helps

Thanks guys,

I will try and clean the AAC valve today and tomorrow and let u konw how it goes. - i think there is a DIY on this site some where just need the carby cleaner and the gasket seal.

I haven't tried a diff AFM only have one mate who has a skyline! i am a newbie to the booster club! :closedeyes:

Thanks guys

NIZ-26T - i have a K+N pod and it just been cleaned!

Cheers

Just got the carby cleaner and gasket goop so i will see how it goes.

CLEANED and no difference still misses on idle (not like a full miss more like a half miss or a short cut)

Edited by RipNGrip

BUMP

Ok update, i have done some more research on this website however i haven't had time to do much more on the car. I regapped down to .8 mm the mechanic just put them in (running boost). Starts start up..... idles fine while still in "choke" i don't know what skylines do but it revs higher and richer.... than gets warm and starts to half miss than full miss......

going to check fuel pressure and check plusitility

going to check air regulator

any thoughts anyone?

Yeh i have two BOV and i have been reading about how it can mes up idle... How do i remove and disable my atmo BOV..... i have two and the atmo sits on the intercooler piling in the corner behind the front left area of my front spoiler..

maybe remove the vaccum piling to it????

Update:

I have checked that all 6 injectors are operating. 6 = all good. Cleaned the AAC no miss on idle but it gets worse as it warms up and on any sort of load...........

thinking possible AFM or aftermarket BOV..

How do u remove/disable an aftermarket BOV that is attached to my I/C piling

Well, i got really drunk on friday so saturday was recovery. Only looked at the car for a bit on sunday. I also downloaded the r32 engine manual (it is quite helpful - answer those a few questions on how to do diagnostics). I got a multimeter and some fuel just so i could have a crack at it for a bit. It seems that the problem gets worse as the car warms up..... it even starts to miss at idle if the car is warm.

So far:

1. placed screw driver on all 6 injectors (click, click, click) come from all of them - so they are pulsing

2. cleaned the AAC valve - it was really really dirty.

3. gapped down to .8mm (iridum plugs - i am having doubts about these plugs too)

4. resoldered the AFM and performed a DIY test which involved 12v battery, fan and multimeter - .5 volts fan didn't make a difference in the voltage so i am wondering if it wasn't powerful enough a fan or my AFM is BONED. I am leaning toward a AFM currently considering it warms up and starts missing on load/on idle. if i unplug the AFM plug the car just runs rich (light black smoke coming out the back) and sorta limps.

possbles:

1. replace afm with a mates

2. clean air regulator

3. BUY more copper plugs with higher heat ranges - grrrrrrrrrr irdiums aren't CHEAP

4. send it back to the mechanic

5. POUR PETROLLLLL on the RB20DET and smoke a cig next to it

6. crank the BOOST and try and destory the car

7. REPLACE WITH RB25 or RB26 after tax time.......... :) dont'[ have that much money for half cut and conversion

Well..... HOpefull i have found the soultion and i will post it for future misfire/stalling/heistating skyline drivers later...

Ran diag mode.

Code 54 = Auto gearbox d/c > auto to man conversion :( - HD exedy

Code 12 = AFM ......... HOPEFULLY found the source of my problems

p.s addition problem which i think worked towards to stalling was a split intercooler piling!

Anyways trying to find an jap auto wrecker with a AFM and i will confirm diagnosis!

Swapped ignitor with working rb20det... no deal! It seems to spit out some small black clumps (feel slightly wet) from the exhaust and begining to think it maybe a head gasket leak which comes to life when the engine warms up! HOwever maybe i should just bring it to a mechanic which specialize in rb20 skylines!

any recommendations guys?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
×
×
  • Create New...