Jump to content
SAU Community

Recommended Posts

Ok, i figured other forums i frequent have them as well

please post as many specs of your wheels as possible

width and offsets being the MOST important

Picture from the side straight on, and one from the front straight on (to see if they stick out, or sink in for fitment wise)

ill start

Stock M35 wheels.

15mm spacers front and rear to clear GTR brakes

225/50/17 tires

17x7 id imagine is waht it looks like

383528502_13d43d07ff.jpg

383528569_5856cb5a76.jpg

Work euroline

18x9 -5

18x0 +20

235/40/18

400501903_42836c68bd.jpg

400501941_265dd452bc.jpg

400501811_a1f0a65d3f.jpg

above is with stock fenders

below is with midified fenders

406702878_99e1df16bd.jpg

406702791_5d46ba756f.jpg

Work Emotion XD9

18x9 +20 all around +20mm spacer on the front

225/40/18

453749229_cabaf516a7.jpg

453749179_9735cbd03b.jpg

please contribute

Link to comment
https://www.sau.com.au/forums/topic/164936-post-your-wheelstire-size-and-specs/
Share on other sites

  • Replies 67
  • Created
  • Last Reply

Top Posters In This Topic

17 x 9 - Standard R33GTR wheels with 245/40/17's

Pictures are at 340 mm front and 330 mm rear, which was too low. It's now at 355 mm front and 350 mm rear, much better ride and handling.

R33GTR_Wheels_340mm_Side.jpg

R33GTR_Wheels_340mm_along.jpg

:D cheers :(

  • 4 weeks later...

18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

Your using 235's on 10 inch rims as per per your first post?

They would look mega stretched?

A "normal" person would use a smaller width rim and run the correct width tyre for comfort, looks, handling and safety

am i normal?

I use a 225/40 on a 9 inch wide and a 235/40 on a 10 inch wide

its about clearance, the stretch in the sidewall allows you to run a wider/lower offset without fear of rubbing so when the camber changes in a turn, it acts like a circle and not a square like a normal tire

am i normal?

NO :thumbsup:

That's why you should explain or clairfy when posting esp when people are asking a question about a topic they do not know anything about. Otherwise someone is going go and buy a set of wheels too wide or the wrong offset and have to beat the shit out of the rear guards and run a way too narrow a tyre for the rim size.

18x10 +20

dont get a 10 in the rear unless you get at LEAST a +10

but hten you will haev to do an agressive roll and pull in the rear.

anything less will hit your coilover.

cool...thanks grant.

mate has a set of eurolines ..18*9 and 18*10 ..both with +35 offset...i'll try them for fit this weekend....oh and tyres are 235 at the rear too...really stretchhhhhed

Running Advanti Racing 'Karla" wheels:

Wheels: 19x8 +35

Tyres: 245/35 R19 Hankook K104

They are being replaced (due to a fault) with Enkei RP03 model which should fill the guards a little more, I think.

post-17581-1179964171_thumb.jpg

post-17581-1179964287_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You can use your VIN to look up the factory part number somewhere like amayama, and then look to order new if necessary. https://www.amayama.com/en/genuine-catalogs/nissan Depending on price you might want to rebuild instead. @GTSBoy I had an interesting insight into US market parts when the Titan rear calipers were sticking. New calipers were dirt cheap, about 20% more than a rebuild kit....they are just considered throw away maintenance items
    • Funny, but really not funny. Thank god (most) f the world has moved on since then
    • Lots of votes for driving onto a plank first; that is the quickest way I've found, 25mm is enough for my case but that will vary by car It also depends where you are going for. On the 32 I can get to the rear diff with my floor jack if I do that end first, and get it up on stands. Then I lift the front from either front tow hook as high as needed, also onto stands. Sometimes I need a small lift on the other tow hook to get it level enough If I do the front first I can't get to the rear diff because of the angle of the car Other options are getting to the front mount of the rear subframe from in front of the wheel (if only lifting one side, or just do both which is a bit of a pain compared to one lift from the diff), or also the gearbox cross member mount on the driver's side if you are  just trying to lift the driver's side. I This is the jack I use; it says 75mm clearance but of course that is only on the lower section so if you have to reach too far in like the diff you still get stuck. https://www.snapon-bluepoint.com.sg/category/Floor-Jacks/product/Floor-Jack,-2-Ton-Low-Profile
    • On the bright side, the weather will turn much nicer for working outside shortly....sounds like you might need to start on a neighbour's garden next
    • Ok so i will NEED to have this sensor anyway even with Nistune (or standalone ECU) https://justjap.com/products/genuine-nissan-boost-pressure-sensor-evap-control-system-fits-nissan-r34-skyline-c34-nm35-stagea-pnt30-x-trail-rb25det-vq25det-sr20vet?currency=AUD&srsltid=AfmBOoqfxX48bW9bEwH62orcNhtBfp7ekAL0C9Ca89ySFGUiBzXfXeze Is this the correct one? And this is only thing i need? No other "things" connected to the sensor or something? I do have the wiring.
×
×
  • Create New...