Jump to content
SAU Community

Recommended Posts

i also have the PSI Drift/Stealth wing which will be going on very soon.

Col: they would not be readily interchangable as such. the Drift wing does not have the same mounting system as the factory items; it is held on by an adhesive and tek screws where the factory wings use fancy clips (which i smashed when removing)

well i could definitely never get mine off now because it was stuck on with urethane and then painted the whole boot and wing together so it looks like the wing is part of the boot and gives a really tidy look, to be honest i wish it sat down a little lower though.

I have just updated the shipping prices in the above post. However if you want the most accurate price for your location please visit our site and put in your postcode to get an exact shipping cost.

il be in contact in the near future. definately is the best price around. does any1 wanna buy my big veilside 1? its on here for sale i think with pics.

I have just noticed that joe blo has made 2 x posts

1. Where can i get a fully sick drift wing cheap?

2. Where can i get a screamer pipe cheap?

>>>>> Boost crusin is thata-way >>>> www.boostcruising.com

I have just noticed that joe blo has made 2 x posts

1. Where can i get a fully sick drift wing cheap?

2. Where can i get a screamer pipe cheap?

>>>>> Boost crusin is thata-way >>>> www.boostcruising.com

i asked if i can get the wing in brisbane to save on postage. im sure most people wudnt mind saving 50 dollars?

the screamer pipe thread was asking if any1 knew where to get 1. i didnt mention cheap. is there a problem with trying to find parts at a better price or to ask where to get something after looking for ages? im also a member on boostcruising. not a bad site but asked on here coz there for skylines

lick my balls dude

  • 1 month later...

anyone know where you can get a slightly higher stealthy wing? i like the lip, but i want something with a tiny bit more height. also if there was one with a little gap between the rear wing part and the boot to let water drain would be excellente'!

Does anyone have any remedies for stopping water leaking into the boot area/taillights? I know its a common problem regardless, hoping a bead of silicone will stop a majority of water leaking in. Only really noticed it with all this rain of late.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...