Jump to content
SAU Community

Recommended Posts

HI,

Im going to the dyno and thought Id post up to see if any1 can guess how much power I will make...

Mods are

-r33 Rb25det stock

-Automatic

-Hi-flow turbo - R33 front hi-flowed and VG30 rear housing. Other specifics unknown.

-FMIC

-3inch exhaust with split dump, wrapped. Old hi-flow 2 mufflers, quiet.

-Rb20det wastegate actuator 10psi

-SAFCII

-Stock fuel pump, no reg, stock AFM.

-Thats it..

Getting tuned by HITMAN at Race Solutions in Penrith.

I will post up results hopefully tomorow...

Have a guess...

Disclaimer: No prizes included. :D

Cheers Liz and Daniel

________________________________________________________________________________

____

I GOT RESULTS BACK - We are suprised with the results and Matt done a great job....

234.9RWKW@11/12psi.( I dont know why it ran the higher psi as it has an rb20 acuator on it.

Only issue I had was with the spark plugs, it was blowing out the spark at this boost level, there copper and were gapped to 1.1 now Matt regapped them to 0.65.

He didnt mention anything about fuel, afm or anything and they were working quite well at this boost level..

I am curious to see what it will do when i finish what I want to do with it, just a few more minor mods.

AFR's were good to between 11.8 t 12.0.

________________________________________________________________________________

_____

After all this now to the next stage..

The plan is to go to WSID on anzac day...GUESS what time I will run????

Im thinking 13.5@105mph with a 2.2 60ft as the car doesnt move much until 4000rpm where is wheel spins until second then just pulls and pulls...im just worried about the auto...getting heak soaked/slipping or dying..

________________________________________________________________________________

________________

Update;

AUTO DIED 4/5 months later..Going manual now and modifying a little more..See page 3 for full list of upgrades and changes.

post-28122-1177063692.jpg

post-28122-1177063726.jpg

  • Replies 58
  • Created
  • Last Reply

Top Posters In This Topic

Im hoping to do that before the Sau dyno day..but money money money...

I want to do a few more mods, so it can handle 18psi.

Im yet to decipher if the SAFCII is up to the task of running the engine safely at anything above 18psi..

Cheers

its how well the tuner can tune it

but it will become a comprimise solution at some point in time

there will be a point where its advancing the timing too much

which induces detonation so it will drop the low octane map

so you have to back it off a little and keep it conservative

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...