Jump to content
SAU Community

Recommended Posts

Ok long story short.... :rant:

I own a R31 RB20DET, and getting a kit for it is nigh on impossible unless I fork out over $2500 for the R31 House kits, which, for a drift car, is a little silly.

Ive been looking at a Lot of R31 House's cars and they use a lot of other cars kits ie Ceff and Laurel, modded to suit the cars.

Im after the Side skirt dimensions for All 3 of the above mantioned models, as you can buy copy kits rather cheap.

I already have a R31 House copy front lip, and was considering C33 laurel URAS sides and rear, but wish to know dimensions before I do anything.

veloce3248img600x450117vd3.jpg

A31 URAS side skirts^^^

gtw4dk0.jpg

C33 Laurel URAS sides and rear bar^^^

To me it seems they cut the rear bar and fibreglass it onto a stock rear bar.... and the A31 URAS sides are simply cut to fit....

Heard a few rumours that R32 4 - Door sides fit, and if so, a set of Vertex sides would do the job quite nicley. :P:(

Ive tried emailing R31 house, using a translator, but I got a reply in Kanji and I cant translate it. :rant: :rant:

I know that some think kits and such are stupid, but Ive pretty much done everything else, bodykit and paint plus my cage(which goes in on the 23rd of june) were the last on my list.

To sum up, Im after Side skirt lengths on the Above mentioned 3 cars.... A31, C33 and R32 4 - Door. Need the actual length of the side of car, not the sideskirt.

Thank you all in advance.

Ben. :):rant:

Edited by R31 drift pig

Already looked there... tried URAS aus, Monkey warehouse and Jetspeed.... they didnt have any in stock to measure. Im not ordering them in if they wont fit. :)

Trying Viva Garage tomorrow

Anyone? Just need someone torun out to their car with a tape measure and get the bottom wheel arch to arch measurements (where a sideskirt would bolt on) for a C33 and 32 foor door... mate has a A31 and checking his tomorrow arvo.

Any help would be appreciated. :):(

Thanks Guys.

That would be much appreciated mate.... >_<:yes:

Now for a C33 laurel owner.... :santa::thumbsup:

And yes, that red 31 coupe is the hottest thing ive ever seen. RB26DET as well

Cheers, Ben.

Hey ,

a31 and c33 are identical for side skirt fitment.

I have a pair of Uras skirts that I want to get rid of as well as a rear bar to suit cefiro.

Where do you live ?

Could do some trial fitting???

PM me.

PM'd you about those sideskirts previously....

You have new PM.

Cheers for all your help guys...

  • 11 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few suggestions: Do you have the option of retarding your exhaust cam gear to bring the power band over to the left? VCT would be turned off after you make peak torque, you see the power/torque will decay faster with it left on all the way to the limiter Once VCT is turned off, you'll find the motor will take a bit more timing being ramped in Send its mum, more boost! Of course, depends on your exhaust pressure.
    • Tow a boat... people won't know wtf is going on 🤣 
    • I was back on the dyno again yesterday after completely revamping my methanol injection system. I was making 440kw at 19psi. Great, this is more then I was making last summer with my old meth system at that pressure, and I figured it would be smooth sailing up to 30+psi. We continued increasing from there and by 25psi, I had only hit 455kw. Dyno sadly lost utility power at this point and I left. We seemed to be on course to hit the same power wall as last summer (477kw@27psi). This is a built RB25 S1 stroked to a 2.8. Built and ported head with Kelford 272/262 cams. Precision 6466 Turbo. Tuner last year believed the power wall is a mix of RPM limitations (Hydro lifters/Limit set at 7600RPM) and fueling. With my new meth system, we're seeing zero knock now but it still won't go up.  What else can I do at this point? Here's my train of thought.  - It's clear from the dyno graph that I would easily make power to 8500+RPM but I'm limited to 7600RPM. I could risk increasing my limiter, but hydro lifters have me worried. What are my options here besides going NEO head or solid lifter conversion? I'm rocking a 1.05AR turbine on my 6466. Would dropping down to a .84 help shift that power down in anyway? - We're only seeing roughly a 30kw difference at the top end with VCT on or off. Is this normal? I want to confirm VCT is working properly. - Should I look into other cam options?  - Should I just keep increasing boost and see if she wakes up later on? I would expect to hit 600rwkw around 35psi with my 6466.   
    • First thought is to use a ram mount (to hold the ipad) + windscreen suction mount. The arms on the ram mount can be as long as you like, should be able to position the ipad pretty well with that setup. 
×
×
  • Create New...