Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...
  • Replies 95
  • Created
  • Last Reply

Top Posters In This Topic

As Title R33 series 2..........whole car wrecking........

Complete engine with turbo 53klms on clock (SOLD)

s2 reo (SOLD)

gear surround (sold)

SELLING EVERYTHING NOW, PM ME IF I HAVE FORGOTTEN TO ADD TO LIST

SERIES 2 STUFF:

L Headlight $250

s2 bonnet $450

manual s2 DIFF $450

Front seats $300

complete Back seat $200

Dash speedo / klm etc complete $200

Gear surround (MANUAL / very clean) $90

Gaurds $150 each

Doors $200 each

boot lid $150

series 1 boot lid spoiler $75

Taillights $125

Complete airbag set/dash/ 2 airbags/sensors $1500

Complete 5 studd conversion / hubs / rotors / calipers all what u need ...$900

SERIES 1 STUFF:

R33 series 1 Bar complete $200

R33 series 1 reinforcement $200

R33 series 1 bonnet $200

R33 series 1 headlights $450 pair

R33 front bar blinkers $100 pair (will separate if needed).

Thats all i can think off at moment.

IF NOT ON THE LIST ABOVE LET ME KNOW WHAT U NEED AS CAR IS STILL MOSTLY COMPLETE.

post here or PM me / If u want let pics let us know and i will email them or post here later.

SYDNEY. but willing post / courier.

Hi mate, I'm interested in ypur rear brake setup including calipers, rotors and handbreke mechanism. Do you still have them and if so are you willing to separate them from your brake packag? and wherabouts in sydmey are yoy?

john

  • 1 month later...

hey im after both front crash sensors are you willing to separate them from the airbag stuff?? if so pm me a price + delivery to melb

red back = arnt the climate control units same anyway??

r34_boy = pic emailed

kinks = Will take a pic soon and send it

Tak = pmed you will get price on courier.

sorry for late reply ...........

Thank guys............

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
    • Ooo I might actually come and bring the kids, however will leave the shit box home and take the daily
    • Thanks. Yeah I realised that there's no way I'd be able to cover the holes with the filler, it would just fall through. Thanks again @GTSBoy!
    • That was the reason I asked. If you were going to be fully bodge spec, then that type of filler is the extreme bodge way to fill a large gap. But seeing as you're going to use glass sheet, I would only use that fibre reinforced filler if there are places that need a "bit more" after you've finished laying in the sheet. Which, ideally, you wouldn't. You might use a blob of it underneath the sheet, if you need to provide some support from under to keep the level of your sheet repair up as high as it needs to be, to minimise the amount of filler you need on top. Even though you're going bodge spec here, using glass instead of metal, the same rules apply wrt not having half inch deep filler on the top of the repair. Thick filler always ends up shitting the bed earlier than thin filler.
×
×
  • Create New...