Jump to content
SAU Community

Recommended Posts

ah kool just need to keep in mind who to get quotes from for my damage

ill get the add for you tomoz after work k just call and say u done a mates r33 4 door repainted doors and fitted new door handle that sme1 tried to break into about a month ago say his name was allan can u give me a quote on what you want done and he should be able to sort you out mate. P.s Got left hand door keyed on weekend at shops c**ts!!!!!!!! around tthree inch long damn :whistling:

I know of quite a few people with cars bolted to the floor. You can get chains & Padlocks that were developed for motorcycles that CAN'T be cut with bolt cutters etc. Would have to OXY them off... good luck! LOL

Last night had an interesting situation....

Went back to work at 6:15pm last night to pick up phone (left behind). Parked near the roundabout just past KFC down the bay (opposite side near Mitre 10). Grabbed phone, came back out, into car. Had lights off, car off, sitting in there looking for something i dropped on the ground and a Silver 200sx (s15) pulled up just down the road on the left. No indicator, just sits there. It then started reversing slowly towards my car, when i popped my head up after a few seconds of noticing this car it then all of a sudden took off.

Basically in short i watched the car creep in reverse from 30m away to within 3 when i decided to pop my head up - bang - they took off. Had tinted windows and what looked like 18-19 inch gunmetal grey rims. I turned car on, reversed, then took off, by that time they turned onto Tapleys and were gone pretty darn quick.

Not sure what the idea of this car was as there were no others around, and no place was open and it was raining. Just thought i'd let you guys know. Sorry for the essay.

Dan

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...