Jump to content
SAU Community

Recommended Posts

  • Replies 102
  • Created
  • Last Reply

Top Posters In This Topic

yes mate i can send it there.

will check price first thing in the morning.

send ur postcode asap and i will send u my account details.

if anyone would like postage prices i will be at the post office in morning.

please say if u would like something but please beware that some people have already asked first so please dont be dissapointed.

sorry it has taken a while to get pics but hey its a lot of parts to get out an take pics of whilst working a day and night job.

sorry for any inconvenicnce.

if u would a pic of something else not shown please ask and u will recieve.

so is the dash sold or still for sale

please advise as i will pay today

i need the centre guages down the gear stick so A/C the lot

Edited by XXE-R32

PMS relied XXE-R32 u have a pm

cant beLive how many tyre kickers i have had on parts.....meh

come on guys makes reasonable offers.....i will not answer low ballin PM's on parts.

ALSO I HAVE THE ROOF SECTION AND THE REAR CHASSIS CUT OF THE CAR FOR SALE.

PERFECT FOR FIXING A REAR ENDED R34 2 DOOR.

Hi mates do you still have cluster and steering wheel don't worry for airbag I just want steering wheel.How much for both and post to melbourne. And how much each to post to melbourne.And how can I pay you if I want the parts .ThanksAnd one more thing do you have heater fan too and how much thanks

Edited by bobby09

What about the seals on the outside of the doors?

The black plastic/rubber sections that push against the window from the outside.

I think you would call them the outer door sill seals.

sorry guys been in hospital last week. came down with illness.

pm's replied.

steering wheel is sold sorry.

HOTr34 ...bits will be on its way in 24 hours.

badges were taxed by thieving bastard.

Andi ....how much of the trim did u want?

the side moulding bits?

boot mat?

still have seats now ...tyre kicker didnt want them ....no cash to tell truth.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...