Jump to content
SAU Community

Recommended Posts

UniGroup was the first ever workshop I went to for an SAU dyno day many years ago. Their attention to detail and professionalism is quite rare in the industry.

Edit: I've also been to JEM for a dyno tune but dont have any other experience with them.

Edited by benm

I highly recoomend Yavuz from unigroup. He is a top bloke.

Go for the premium tune with them. Cost about $600ish but he has your car for 3 days and he tunes everything..

Cold start, idle, partial throttle etc etc.

Also for 12 months he will do tune and check up on your car for free, if anything goes wrong or your not happy.

Thanks fellas. How about unigroup? Unigroup is closer..trying to decide between the 2.

my old cars were both tuned at unigroup.

they're good. the owner Yavuz is a good bloke too, very helpful.

fast delivery, excellent service!! a++++++++++

lol

  • 2 weeks later...
I used him a few weeks ago, PFC tune with stock turbo,FMIC, 3inch exhaust, fuel pump tuned it at 10psi low and 13psi high, made just under 200rwkw. I recommend him.

I'm sorry but i have to take back this statement. Not happy with my tune.

Done anything about it?

Hi Adrian,

Yeah, without going into it too much it seems the PFC has been tuned wrong. If you'd like to know more PM me and i'll discuss it there, I don't want to say anything bad about Adam as he seems he knows what he is doing, but unfortunately it hasn't worked for my car.

gee 180, yes bud i have taken it back and still not fixed.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...