Jump to content
SAU Community

Installing Hks Gt-rs Questions: Banjo Bolt Position, Copper Washers, Oil Drain Gasket..


Recommended Posts

Hey guys,

I've started taking off my stock turbo and at the moment everything is unbolted ready to be pulled off except for the damn water/coolant feed line, those brackets that hold the lines steady are f*ckers to get off being behind the engine and all.

Anyway with the new braided lines and banjo bolts I wanted to know whether or not I had to try to line up the hole in the bolt to the hole off the line? I'm guessing to do this I'll mark the top of the bolt with a market or something and make sure its running straight with the lines? Or would the oil/water run 'around' the inside of the braided line ending (whats this called?) and find its way through the hole?

Also, I seemed to have only recieved 2 thick (I mean alot thicker than the standard ones) copper washers. I'm planning to buy a whole bunch of new ones instead of using the standard ones and afaik copper washes are curved and need to be crushed. So does it matter which way I put the washer on or does the curve side have to faced specifically? Can I just use thin ones I can get from any auto store or do I need to find THICK ones like the 2 that came with my turbo?

And lastly, where can I get a oil drain gasket? It's that weird diamond looking shape thing?

Any help will be appreciated, thanks in advance. :laugh: Would really like to get this all done by tomorrow.

Thanks,

Andy

Oh I forgot:

How many bolts with a oil restrictor should there be? Is it just 2? Both being the oil feed line, one on turbo and the other on the block?

I only got one bolt with a restrictor, can I just re-use a stock bolt on the block if one is there?

the hole in the banjo bolt doesn't have to line up with the flow path of the banjo. just bolt it in tight.

some copper washers (called crush washers) are dome shaped so they are desinged to do one way, but it wont matter too much for you as they are sealing on both sides.

i would say just one restrictor bolt is fine.

1. Use their banjo bolts

2. crush washers are good. Nissan DID NOT use crush washers stock, and they didn't leak. But I like crush washers - about $20 for the whole set at pirtek. I put the thin side up towards the bolt head (if you think about it, the turbo has a bigger edge, bolt head might be smaller). Usually the crush washers are really small though so would work the other way too.

3. water line behind the block is easy. I just did one the other day. The line reaches around the other side of the block and joins with this other rubber hose. What I do, is I undo both brackets, then take that rubber hose off too from the other side and pull it through. The bracket on the side can be undone easily, the other one, I used a spanner that I cut in half, and put down through the coilpack cover gap.

Thanks guys. Got some copper washers from Pirtek and got the turbo off yesterday. Heres some pictures of stock and the GTRS side by side.

I got some teflon tape as well, should I bother using it on the bolts? Pirtek guys told me I should use it for the coolant feed line where the silicon line joins the braided line with an adaptor.

And where can I get a gasket for the oil drain adaptor? Or can I just use any old gasket paper cut out ot the right shape?

post-8121-1179544594_thumb.jpg

post-8121-1179544600_thumb.jpg

post-8121-1179544607_thumb.jpg

post-8121-1179544614_thumb.jpg

Edited by Andi

So did everything bolt up perfectly? or was there things that you had to modify? would be keen to know if you had any problems fitting it.

Cheers

Cool,

Got a part numer Manwhore?

I just used teflon on the bolt<->line connection. Also how much am I suppose to tighten the banjo bolts? Keep on going until it 'feels' tight enough or until it stops?

Cheers!

I did my banjos up tight, but not give yourself a hernia tight. Nowhere near the maximum I could tighten them - they seem pretty soft, so it looks like it's possible to turn the head right off them if you go max tightness.

The way that a wiseman described it to me is the washers are just like your sump washers. Do it up as tight as you'd do that.

What I found, is that there's plenty of room to check and tighten after if needs be anyways.

No part number - just tell them what you need, they'll look it up.

Sorry no more pictures, the turbo is in the car now with everything bolted up.

I primed the turbo by unplugging the CAS and kept cranking until I saw oil pressure. Then I started her up and let her idle for 10 minutes.

I threw a cardboard mat underneath to check for leaks and thankfully it didn't seem like anything was leaking but it was abit dark so I'll make sure again tomorrow.

That said, I do have one concern. I smelt something in the engine bay like it was a light burning/cooking smell, I think its the water line or something. I flushed the coolant and poured a whole new bottle of Nulon Red 5 Year Concentrate 2.5L with ~3.5L of Distilled water, could this be the smell?

Also, I've noticed that some of my braided lines are abit long. Are they suppose to touch nothing else at all? My water feed hose off the block goes all the way around to the turbo side and connects to the braided line to the turbo just abit under the rocker cover, is this okay?

Again thanks all for the advice! Really appreciate it as its helped me heaps. :)

EDIT: forgot to say that some of the lines are sitting on other things. Like the water/coolant braided feed is sitting against the dump pipe, and the oil feed is sitting against the turbo etc. I did make sure none of the lines are touching anything that could potentially melt/burn. Is it okay to leave it against metal things?

Edited by Andi

Nope, it's perfectly normal to smell. it's burning oil. You're bound to have a touch of oil when installing it. Think about how hot the exhaust gets. First time I saw that I shat myself, but nah, you're right, as long as if there are no leaks etc.

Not good for lines to sit on the exhaust housing or dump. I always make sure that they clear.

Thanks for the quick reply Manwhore. So make sure ALL the lines are clear yes? Its okay for the rubber/silicon water feed line to be touching the block of couse right? I re-inserted it back into the coilpack cover thing.

In regards to the silicon touching the block - who knows. I suppose it's safe to say that no sort of plastic/rubber/silicon likes heat. It's all a matter of how much. I'd try and keep it off the block (if possible). Even though it doesn't get crazy hot, it still gets too hot to touch - try touching your cam cover after a long drive (don't, i'm just saying).

I'd try and keep it off if possible, but if you really can't, then hey, gaskets touch heat, but they do die after like 5-10 years.

I mean, I know the turbo catridge gets hot and everything, but I just don't see the need to have an additional line sitting on a glowing exhaust housing/dump. The stock setup wasn't like that, so I try and keep everything off the hot stuff. It's nice and neat anyways.

I'm sure your braids are probably a bit longer. They usually are, since people prefer that then making them short. You should still be able to work with it.

Hope that helps

you should've insulated the braided hoses before putting them on, especially if they're sitting close to the turbo/exhaust/block. braided lines are only beneficial if they arent touching anything that hot.

I don't think it's really good if any line touches the dump/exhaust housing. Even the stock lines on my car, I made sure they weren't touching. They were in the beginning, but I massaged them out a bit.

It's fairly easily possible to install the braided line without touching the housing/dump. Insulating is a possibility, but i find it easier to just get the right length, and position them well.

id never use a straight line for an oil feed for a turbo. the reason why the standard one has that loop in it is so oil stays in there when you shut your motor off, so oil pressure is reached earlier as the motor kicks over (so turbo doesnt fcuk up).

are you going to be monitoring where they go when you're on boost and pulling a fair few g's on a track or at the drags? unless you hire a smurf to sit in your engine bay, i'd doubt you'd ever really know.

then say when they're swinging around they get caught on something hella hot? how often do you check your lines?

Thanks for input guys. I've managed to play with the water/coolant feed line and its no longer touching the dump but is now resting against the gearbox housing, this is okay Manwhore? Its abit hard to manuvoure it without disconnecting the line which would mean coolant pissing out everywhere.

I checked my coolant return and that doesn't seem to be touching anything so thats fine, but the oil feed line is touching a pipe. I think it may be one of those AC pipes, heres a picture to show. Should this be okay?

Sorry for all the questions guys, this is the first time I've installed a turbo and I'd like it not to die on me. :)

EDIT: Joe, when you say insulation what do you suggest to use? I wouldn't mind doing the coolant feed line as it is fairly close to the dump pipe.

Edited by Andi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...