Jump to content
SAU Community

Recommended Posts

Tried to search but didnt find any good answeres..

Installed my Power fc today and started the car, got a good idle after a while and 10 min later i turned on the aircon.

The idle bounces between 400 and 1200 rpm and dosent stop.. somtimes it idles fine for a while but starts bouncing again, oftenly at the same time as the ac turns off.

had the car running for 1,5h but it doesnt get better.

Does anyone have a solution?

Car is R33 GTR V-spec with basic mods, filters, exhaust, larger ic.

/Fredrik

Edited by Fredde

I had the same probem in some of my cars with a power fc. I found the learn doesnt really do much. You need to tune the load cells where it is bouncing. I found that adding some fuel to the cell where the revs dop can stop the idel dropping. You can fiddel with it or bring it to a tuner should be fairly easy to fix.

how strange. do you see anything wierd in sensor sw check when the revs are going wonky?

whats battery voltage like when u are doing it? have u done DATA INIT and tried it again?

is the engine warm when u try it ? what if i try it again and skip air con test and just let it do its self learn idle

how strange. do you see anything wierd in sensor sw check when the revs are going wonky?

whats battery voltage like when u are doing it? have u done DATA INIT and tried it again?

is the engine warm when u try it ? what if i try it again and skip air con test and just let it do its self learn idle

Not what i can remember, the only activity in the sw check is the ac switching of, then the rev drops and starts bouncing.

didn´t check the battery voltage, the batt is quite new so i doubt that it would cause the problems, can check it again though.

I also tried to reset and start all over again a few times without any changes.

The engine was warm when i did the self learn, will try without switching the aircon on.

Is there any sign from the pfc when the self learn is finnished or that the self learn have started/is processing?

I also saw some people having problems when they had a a-lsd, could it be related to my problems since i have a v-spec?

But that was more about the a-lsd light, mine doesnt show anything strange

Regards

Fredrik

the self idle learn takes 30 minutes approx

there is no signal or notice of when its finished, u just have to let it idle unforuntately

try doing it again but skip the aircon part and just let it idle. then once done power it off, back on ensure idle is stable.

then try and turn on the aircon see how that goes

the a-lsd issues with the PFC only appies to the GTST with the active lsd fitted factory

as the gtst PFC does not relay the TPS signal to the a-lsd puter in the boot, you wont have this issue on your GTR

Ok, will try without the aircon later today (it´s still early in the morning here in Sweden).

Oh, forgot to ask in the last post..

Should i see any changes at the idle point in the ign/inj maps after the idle is set or where does it store the "self-learned-idle-stuff"

Thanks for the help >_<

/Fredrik

Problem solved!

Did try to redo the idle setup but had the same problem, even without anything on..

Added some fuel to the idle cell got rid of the rev-bounce so i did a complete reset and added fuel to the idle cell before i started the car.

After that everything worked perfectly.

Thaks to everyone who answered :kiss:

/Fredrik

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
×
×
  • Create New...