Jump to content
SAU Community

33 Box Into 32

Simon-S14
 Share

Recommended Posts

Simon-S14 Grand Master

Simon-S14

Posted
Posted

I know this has been covered several times, i did search but i couldnt acctually find any info that was useful. So theres a couple of things i want to know.

-What Gearbox cross member is used? 33, 32 or what? and does it need to be modified.

-When making a custom tailshaft, what have people done in the past? i wish to retain a two piece shaft, can someone give me the measurement in length for the front section? ( i dont have the box or motor in the car yet and i want to get a shaft made up beforehand)

-Does the shifter line up in the exactaly the same place as the RB20 box?

-What shifter is best to use? I dont have my RB20 box anymore (had a CA shifter in it anyway which was shorter) shoudl i use a 33 one or what?

cheers all!

Simon

Link to comment
https://www.sau.com.au/forums/topic/169714-33-box-into-32/
Share on other sites
Simon-S14 Grand Master

Simon-S14

Posted
  • Author
Posted

im doing it this weekend lol. I mean i'll probably figure it all out when i do it, but it would be nice to have the info available now. I was planning on doing the tailshaft myself on a laithe and reweld together. Then pay for it to be balanced. Hence the need for exact mesurements.

Link to comment
https://www.sau.com.au/forums/topic/169714-33-box-into-32/#findComment-3136105
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Rb26/30 build

      By MBS206 · Posted

      And if you want more power, more reliably, and cheaper, go get the Aussie RB... The 4L Barra and put that in instead.
    • MBS206
      Nismo rear spats

      By MBS206 · Posted

      No cats will keep discolouring the rear bar. Sends white paint a weird yellow stain. Cut and polish normally gets it out, but you'll be doing that every fortnight I found.
    • Butters
      Rb26/30 build

      By Butters · Posted

      Both heads will be equally reliable or unreliable depending on what you do to them.  Stock the RB26 head will flow more. You have access to the stock intake ITB manifold on the RB26 cheaply which flows really well(1000hp+).   Arguably more aftermarket support for RB26, though in Aus we love our RB30 SOHC heads too.    The only downsides to the RB26 head is if you have a VL commodore and want to keep the SOHC look.  Where you may have an issue is drilling out the rb30 block for the bigger head studs but if you are building a big power motor you'd probably put bigger studs on the SOHC head too.  This is just about finding a good machine shop, sometimes easier said than done.  RB30 head worked can make big power just like a Rb26 head, so really it actually more comes down to what your preference is for your car.  People now even making billet versions of both.
    • GTSBoy
      Rb26/30 build

      By GTSBoy · Posted

      2630s work perfectly well. There is something to be said for just using the 30 head, as it saves all the pain of the conversion, still makes tons of power, still sounds cool, etc etc. 2630 will obviously make more power again, but the differences are not stupidly big. It really depends on whether you're racing for sheep stations or not. If it's dead serious, then it's a 26 head. If it's just for fun, it could go either way. But the 26 head and the effort to get it set up, etc etc, is part of the fun.
    • lilley's gtr
      Rb26/30 build

      By lilley's gtr · Posted

      I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
×
×
  • Create New...