Jump to content
SAU Community

Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

i thought u sold the boost controller already? why post the pic of it? ANYWAYS I WANT TT AND BOOST GAUGE. thanks - need pics 1st though. ( i know u wrote boost gauge is sold, but if buyer changes his mind i will buy it) thanks

i just sold boost gauge and apexi air filter this evening. the boost controller reason why i posted pics is coz the aftermarket air flow sensor is still attached at my car and it was pretty late at the workshop earlier and everyone was tired to do anything. so i couldnt remove the air flow sensor this evening and tomorrow morning or afternoon i'll do it.

Hippy and I met up earlier and i showed him the boost controller but he will make the purchase together with the air flow sensor. so it is not sold yet. but pretty soon it will be.

I presume it'll fit a r33 then. Sweet I'll take it if u decide to sell it to me. PLEASE SELL IT TO ME! I did shotgun first thanks. How abouts do i pay u? transfer via a/c or wat?? I've never done this b4

Originally posted by Nozila

btw in relation to the tt, ill would like to buy it off you if it aint sold yet. thanx.

Originally posted by NitRaTe

Dooky, no problem. it's sold to you.

following this reply, is it your fault or mine - im assuming its yours. thus i didnt do things without others knowing if you know what i mean.

Dooky, no big problem on my side, just on bryan's. By the way, it isnt your fault that you thought it was sold to you cause I would have thought the same if I was in your shoes, however, it is just courtesy to give the person a call before rocking up and taking the thing "off the shelf" so to speak. I was left surprised to be honest.

GTST - check your pm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...