Jump to content
SAU Community

phaT R32 GTS_T with GTR engine

ice180

By ice180,
in Victoria

 Share

Recommended Posts

ylwgtr2 Grand Master

ylwgtr2

Posted
Posted

the suti vehicle supplied to fors for any vehicle under low volume compliance wouldve had the original engine in it...therefore each signed off vehicle must be up to the suti vehicle specs.....especially under sevs....either he changed engines or a dodgy 045 was done

inark Grand Master

inark

Posted
Posted

it wasnt under the SEVs it was under the old rules i think... and this one above comes in under the 15 year rule so does it matter what the mods are to it?

i dunno... either way hes got two monsters :O

ylwgtr2 Grand Master

ylwgtr2

Posted
Posted

i think you will find the emmision data that will need to be submitted for a particular model still requires the original engine for that vehicle to be fitted....15 years or older they still have to meet emmision rules....i think everybody is not fully informed in regards to the 15 year old rule...... and sevs came in over a year ago when did this guy get his cars plated?Even under the old system (before sevs)...the vehicle must be up to the suti vehicle standards...engine swap is NOT allowed......

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...