Jump to content
SAU Community

What Is An S1 Engine?

Informer
 Share

Recommended Posts

SilverECR33 Veteran

SilverECR33

Posted
Posted

Nismo S-tune S1 engine is a nismo engine , yes its something special, its better than your stock nissan one. nismo made S-tunes for each model. You will notice the middle one is the nismo 400r which possibly utilized a Tuned version of the S-tune engine :) can anyone confirm?

Rezz Grand Master

Rezz

Posted
Posted
I've seen some GTRs with S1 engines, according to Nismo they have around 400ps which is not all that significant compared to what one can do to increase power. Are they overrated or something special?

I see you're comparing the S1 engine to something alot more 'unstreetable'... are you asking because of the low bang for buck value it seems to have on paper?

The S1 engine are for increased power and torque across the rev range, giving a useable boost in those areas with less stress on the engine. It's a 'street performance upgrade' for GT-Rs (and others) and outright power is not the main focus. Think of it as a higher power RB engine from the Nissan factory, with all the reliability that goes along with it.

ike Collaborator

ike

Posted
Posted
Thats not a 400R.

The 400R has a REINIK 2.8 litre engine called RB-X GT2 (N1 block with forged internals etc etc) 400bhp 478nm lazy

S1 is a rebuilt engine with N1 parts has 400bhp 450nm by nismo

R1 is a N1 block with N1 parts has 450bhp 480nm by nismo

F-Sport is a 2.8L engine with GT block and mostly Gt parts like the Z-tune not sure of the power

hope that helps

ike

ps saw a N1 block (new) on Japanese yahoo for A$1400 GT block was A$4500 new on yahoo nice start

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...