Jump to content
SAU Community

Recommended Posts

As anyone that has met Kel and I will know, we aren't exactly the same height - and that means we are forever sliding the bloody seat backward and forward.

Did any w34 stageas come with electric seats? would love to upgrade if we can....am hoping the wiring is pretty straightforward so if they do exist, and someone has some could you have a look underneath for how many wires as well

Link to comment
https://www.sau.com.au/forums/topic/171138-factory-electric-seats/
Share on other sites

Yeah but you will be disappointed if you think that they have memory settings like American electric seats 'cos they don't. They are actually slower to adjust than std seats..... just do what I did, make sure that your 2nd wife is the same height..... problem solved.... :laughing-smiley-014:

I dont have any switches for the seat heaters, probably because my console has been changed to the 260RS............. But as to the switches for the seats.

Well the drivers side has the following adjustments:

1. Bottom part Front, up & down.

2. Bottom part Rear, up & down.

3. Bottom part all, up & down.

4. Top part, tilt forward & tilt back.

5. Whole seat, forward & back.

But the passengers seat only has 4 & 5.

whats the heartache with sliding seats forward and backwards? :blush:

Im 6ft8in and the wife is 5ft2in. Ive had the drivers seat rail altered for an extension to the overall rail length.

Wifey drives at the closest possible point to the steering wheel (I cant even get into the seat sideways lol) and Im at the furtherest point away from the steering wheel - all in all almost 1 and a half feet of adjustment. Dont need electric seats to do what is a 1sec pre-startup job :w00t: same goes for adjusting seatbelt heights, adjusting rearview mirror etc etc.

Ahh lovely sounds sweet....will keep an eye out for a set.

Tangles, its not realyl the hardest job in the world to use a manual slider, but I figured if I was going to have an overwieght luxury wagon I might as well go the whole hog :D

  • 4 weeks later...
  • 2 weeks later...

bolted the electric/leather seats today....as usual nissan have looked after us they go straight in, and the wiring I needed was all there too. Only thing I needed to change (wierd) is the seat belt thingy was different between the leather and original seats - so had to swap it over from the old seats

just need to retrim the doors and centre console now :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...