Jump to content
SAU Community

Recommended Posts

I did a search and couldn't really find what I am after.

When I start my car, there is a little puff of white smoke, and that's it. None when i'm driving or boosting, just on start up.

What would be causings this?

Also after that my exhaust has quiet a strong smell, it's had to tell what the smell is of - similar to burnt fuel, but this is constant.

I also had the car dynoed (not a tune or check, was just an open day dyno runs) and they said the car is runnin a bit lean.

What would this be from and how can it be fixed.

My Car is a 32 with a 26 conversion and remapped ecu.

white white smoke, oil, damaged turbo seal.

White steam smoke, blown head gasket due to running lean.

Possibly your injecotors are cloges, pump or fuel filter is on the way out

To test for head gasket, take it to a mechanic and do a gas analizer, this will tell you if there are any hudrocarbons in the radiator water.

To test for head gasket, take it to a mechanic and do a gas analizer, this will tell you if there are any hudrocarbons in the radiator water.

With the radiator, I am getting a new thermostat put in and the radiator fulshed, cleaned and new coolant put in.

Is there another way to check if the head gasket is or on its way to being screwed?

If the head gasket is screwed, what's a rough estimate to get it fixed?

Edited by URAS_33

when u start ur car is it early in the morning when its cold?? probs just the hot air hitting the cold air and creating the normal mist which all cars get when its freezing. Its funny how many people i know who got all scared that theyre car is puffing out white smoke when this is all that it is. just a lil food for thought. It may not be all bad. with the running lean probs ur fuel pump.

I did a search and couldn't really find what I am after.

When I start my car, there is a little puff of white smoke, and that's it. None when i'm driving or boosting, just on start up.

What would be causings this?

Also after that my exhaust has quiet a strong smell, it's had to tell what the smell is of - similar to burnt fuel, but this is constant.

I also had the car dynoed (not a tune or check, was just an open day dyno runs) and they said the car is runnin a bit lean.

What would this be from and how can it be fixed.

My Car is a 32 with a 26 conversion and remapped ecu.

A small amount of white smoke usually means the oil you're using is too light on start up.

Fuel smells nothing to worry about, probably just the seal to the fuel tank/pump, as it's known to perish on the r32 over time.

As for running lean that's bad... if you have a pfc or other ecu what knock reading are getting?

As for running lean that's bad... if you have a pfc or other ecu what knock reading are getting?

It just has the standard computer which has been remaped.

PFC is definatly the first on the cards and a good tune.

Yeah white smoke / steam is really faint and does disapate straigh away. I guess coz I'm new to the RB26 (only had a 25 before hand), I'm sketchin about every little thing thats goin on.

I also get white smoke on cold morning starts but i hope its due to LatinR33's explanation :P

Will have a proper look tomorrow morning if it lingers around or just disappears

Read from a site.

could be antifreeze when it is being burned it has a sweet type of smell and tends to dissipate in the air rather quickly
Sometimes when the head gasket goes it will produce a passage for the antifreeze to pass from the capillaries into the combustion chamber.
Answer 2

If the exhaust billows white smoke for a few seconds when first starting the engine after it has been sitting for a while, such as overnight, and then runs normally, it could mean that the rubber valve stem seals have perished - especially if the vehicle is a few years old and has done over 60/70,000 miles.

Another clue is: does the exhaust smoke smell like fresh, rather than burnt oil.

On cold engine starts, especially, the ECU will momentarily run a rich mixture to get ignition going, then thin it back to normal once the O2 sensor can get an accurate reading. The puff of 'smoke' probably has a sweet smell and would contain a small amount of poorly combusted fuel, some uncatalyzed exhaust, and likely a bit of condensation.
Remember it this way--if the white smoke doesn't go away, THEN you have a problem. If it disappears after a few minutes, it's just water vapor. Part of the chemical equation for the combustion of gasoline includes H20.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Jack the back of the car up, pull that wheel off, pull that sensor out, and put a bore scope into the hole to inspect the outer casing, see if anything looks damaged before you pull the whole thing apart.
    • Ergh... So I pulled the speed sensor out again and the tip was shiny so I think it's rubbing the bearing. The bearing contains the magnets for the speed sensor so I think when the first sensor broke it damaged the magnet ring on the bearing.  This is just a Google image, but there is a hole going to the bearing. So when the tip broke off the old sensor I'm guessing it fouled the bearing... As the magnet is only protected by a plastic cover it would be easy to damage it. So I guess I'm doing a bearing again.   
    • My thinking is that if the O2 sensor is shot then your entire above described experience is pure placebo.
    • Here is the mess that I made. That filler there was successful in filling dents in that area. But in the middle area. I can feel dents. And I've gone ocer it multiple times with filler. And the filler is no longer there because i accidently sanded it away. I've chased my tail on this job but this is something else lol. So I'm gonna attempt filler one more time and if it doesn't work I'll just high fill primer the door and see where the issues are because guidecoat is of no use atm.
    • Ok, so I think I sort of figured out where I went wrong. So I definitely overthinked it, and I over sanded, which is probably a large part of the problem. to fix it, I ended up tapping some spots that were likely to be high, made them low, filled them in, and I tackled small sections at a time, and it feels a lot better.    I think what confused me as well is you have the bare metal, and some spots darker and some are lighter, and when I run my finger across it, it' would feel like it's a low spot, but I think it's just a transition in different texture from metal to body filler.    When your finger's sliding on the body filler, and crosses over to the bare metal, going back and forth, it feels like it's a low spot. So I kept putting filler there and sanding, but I think it was just a transition in texture, nothing to do with the low or high spot. But the panel's feels a lot better, and I'm just going to end up priming it, and then I'll block it after with guide coat.   Ended up wasting just about all of my filler on this damn door lol  
×
×
  • Create New...