Jump to content
SAU Community

R32 Skyline Parts *** Melbourne

kelumzi
 Share

Recommended Posts

kelumzi Community Regular

kelumzi

Posted
Posted (edited)

R32 GTR original badge $20

R32 GT badges

R32 NISSAN AND GTST badge $15

Pearl black R32 rear bumper

Pearl black R32 GTS-t front bumper $50 (in picture there is a lower lip not included and was sold)

Pearl black R32 boot lid no wing holes patched

Pearl black R32 boot lid with GTST spoiler $75

R32 stock airbox and filter (filter pratically brand new, only driven a few k's) $50

R32 reinforcement bar $100

Pioneer subwoofer 12" and box $80

Personel steering very light no boss kit $35

R32 GTST orginal floor mats in very good condition 5 pieces $100

Located western suburb Melbourne

Please PM or call on 0409569906

Pickup and can post postage fee applies

gtrbadgewl5.th.jpgdsc00004ik0.th.jpgdsc00010yt1.th.jpgdsc00026zl3.th.jpgdsc00020yu3.th.jpgdsc00821fn9.th.jpg

Edited by kelumzi
Link to comment
https://www.sau.com.au/forums/topic/172025-r32-skyline-parts-melbourne/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
×
×
  • Create New...