Jump to content
SAU Community

Recommended Posts

r33 gtr short motor

crank $250

pistons and rods $250

oil pump $150

gtr sump modified for rwd $350

stock r33 gtr turbs suit highflow $150ea

gtr injectors $250

r33 gtst turbo very very lttle shaft play $350 (complete)

big intercooler 800x300x80 core looks like old garret core or truck core maybe? 3" in/out $$$offers

other parts to add as cleanup progresses

in brisbane and preffer pickup but will post smaller items.

Found old 3" dump pipe for stock gtst turbo dump and front pipe in one has flexi join and been repaired but still better than stock $100..

stock 33gtst intercooler (side mount) $50

trust td05-16g turbos suit reco $600 pair off gtr high mount setup 380-400hp ea

Edited by rb30dett
Link to comment
https://www.sau.com.au/forums/topic/172575-garage-cleanup-sale/
Share on other sites

r33 gtr short motor

crank $250

pistons and rods $250

oil pump $150

gtr sump modified for rwd $350

stock r33 turbs suit highflow $150ea

gtr injectors $250

r33 gtst turbo very very lttle shaft play $350 (complete)

big intercooler 800x300x80 core looks like old garret core or truck core maybe? 3" in/out $$$offers

other parts to add as cleanup progresses

in brisbane and preffer pickup but will post smaller items.

do u have a rb25det engine loom? if so how much?

wat do you mean "to suit Highflow"?.....are they stock R33 GTR turbos?

I mean they have been sitting in the shed for a couple years and would suit reco? were working when removed but I recomend to atleast put a seal kit through them. or if some one wants to highflow a set without having there car off the road for a long time just do these and swap over then sell yours. hence the cheap price...

Mr simo: I have an r33 gtr compressor if its any good too you.

Edited by rb30dett

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...