Jump to content
SAU Community

Recommended Posts

  • 3 months later...
  • Replies 539
  • Created
  • Last Reply

Top Posters In This Topic

Just read your post from start to finish. 

Good to see the progress from start to finish. 

Did you go bigger in the injectors from the 800 odd cc ones. 

I have a similar setup with the gtx3582r and 1000cc injectors with a 3l built bottom end ported neo head s2 pon cams.

Currently on run in tune. 5000 rpm limit  14psi i see 349rwhp so 260rwkw with no timing as had a problem with the tps. On pump 98. When its run in i will be throwing bigger injectors at it  ew ecu instead of the nistune. 

Hopefully see around 480 to 520 on pump and 600ish on e85. Still debating on the e85. 

All built by myself. Including my own exhaust manifold and 3.5 inch dump pipe and 3 exhaust that i made. 

Bare in mind i have it in a lc gtr torana that tips the scales at 1057kgs. 

20160808_163908.jpg

Resized_20160909_141859.jpeg

20160921_190821.jpg

DSC_8294-Edit.jpg

  • Like 2

Injectors are rotchester 1000cc that flow 1090cc .the e85 road is a good one but its best to keep up your maintenence and not the best to leave your car sitting around for long periods . Also found once you start climbing higher coil packs and harnesses need to be good order .

But with the weight of your car you will shit your self the first couple of times you hit it ...lol if you get a chance to run a 1000 meter event you have some fun in that car.

My next step once i find my other problem out is to run nos again so that 500kw that marko is talking about be achievable i hope . Good luck with the let us know how you go.

 

 

12 hours ago, lcxu105 said:

Just read your post from start to finish. 

Good to see the progress from start to finish. 

Did you go bigger in the injectors from the 800 odd cc ones. 

I have a similar setup with the gtx3582r and 1000cc injectors with a 3l built bottom end ported neo head s2 pon cams.

Currently on run in tune. 5000 rpm limit  14psi i see 349rwhp so 260rwkw with no timing as had a problem with the tps. On pump 98. When its run in i will be throwing bigger injectors at it  ew ecu instead of the nistune. 

Hopefully see around 480 to 520 on pump and 600ish on e85. Still debating on the e85. 

All built by myself. Including my own exhaust manifold and 3.5 inch dump pipe and 3 exhaust that i made. 

Bare in mind i have it in a lc gtr torana that tips the scales at 1057kgs. 

20160808_163908.jpg

Resized_20160909_141859.jpeg

20160921_190821.jpg

DSC_8294-Edit.jpg

That is a very nice conversion but I am biased as well as I have a soft spot for toranas :)

  • 1 year later...
31 minutes ago, WARLORD said:

Thanks

car still providing boners? haven't heard about it in a while!

Also these days, the Bosch 1550cc aka 1650cc (as most retailers call them) are 100% unmodifed where as the 1250cc are still milled to get that flow rating.

yer car is still around just haven't had time to play with it ... I am thinking of reconnecting the nos again with a 75 shot  for something to do but i know the clutch will die. need to find a new clutch,

That will be clutch number 6 since 2006 . ive tried so many types now and only found the jim berry to have lasted my abuse i should of keep it.

2 hours ago, WARLORD said:

yer car is still around just haven't had time to play with it ... I am thinking of reconnecting the nos again with a 75 shot  for something to do but i know the clutch will die. need to find a new clutch,

That will be clutch number 6 since 2006 . ive tried so many types now and only found the jim berry to have lasted my abuse i should of keep it.

may use the nitrous to only get the turbo  on, as a form of anti-lag - would make it like a V8

You still on a single plate? maybe have a chat with Scott at Western Clutch in St Mary and pop in a twin plate.

got a os str twin and i think i have over heated the pressure plate  after killing a lambo and a mclaren  

 

are they good rebuilding clutches 

Edited by WARLORD
3 hours ago, WARLORD said:

got a os str twin and i think i have over heated the pressure plate  after killing a lambo and a mclaren  

 

are they good rebuilding clutches 

They have the right tools to do what you dream of, they have a clutch pressure plate testing tool as well!

I've got a Exedy clutch modified by them to clamp 1.7 tons with a carbotic disc and the pedal effort is like a stock manual Corolla.

27 minutes ago, WARLORD said:

how much for this new addition 

Somewhere around the $1k mark installed (this was a while ago) - yours might be different in price as it's a twin plate

  • 8 months later...
  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Surely somebody has one in VIC. Have you asked at any shops?  Is this the yearly inspection or did you get a canary?
    • This is where I share pain with you, @Duncan. The move to change so many cooling system pieces to plastic is a killer! Plastic end tanks and a few plastic hose flanges on my car's fail after so little time.  Curious about the need for a bigger rad, is that just for long sessions in the summer or because the car generally needs more cooling?
    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
×
×
  • Create New...