Jump to content
SAU Community

Front Mount/blow Off Valve Question

Jamie88

By Jamie88,
in Engines & Forced Induction

 Share

Recommended Posts

Jamie88 Community Regular

Jamie88

Posted
Posted (edited)

Hey all, getting a front mount kit for my r33 and after some advice/knowledge. The pipe my bov is currently on shown in picture is going to be replaced. The other pic shows the kit I am getting, or similar so where is the best place to now put my bov? Would it be better to leave the standard one connected (metal plate blocks the bottom where it joins the intake to stop it functioning) and just get a new adaptor welded to the new pipe if so should I completely disconnect the stock bov or is the plate sufficient enough. Or should just get an adaptor to suit standard position. My main concern is what do I do with the vaccum lines left over if I move the bov and disconnect stock one. I will have the plumback pipe sitting there for the stock bov and the line that connects the the blitz one left doing nothing. I dont know where they should be going if I move the bov, as it was already the way it is when I got the car. If you can get ya head around what I just said help me out please. I tried to describe it as best as I can. Thanks

If you can help me out add me to msn. [email protected]

post-38045-1182154480_thumb.jpg

post-38045-1182154528_thumb.jpg

Edited by Jamie88
Link to comment
https://www.sau.com.au/forums/topic/173262-front-mountblow-off-valve-question/
Share on other sites
blinko Proficient

blinko

Posted
Posted (edited)

yeh where it is now is prob the best place and the only pipe that should be left free if u have a atmos BOV is the plumb back pipe and that just simply has to be covered up... use a grommet or sumthing...

Edited by blinko
Jamie88 Community Regular

Jamie88

Posted
  • Author
Posted
yeh where it is now is prob the best place and the only pipe that should be left free if u have a atmos BOV is the plumb back pipe and that just simply has to be covered up... use a grommet or sumthing...

Yeah but what im saying is when I get my front mount, the pipe its on now will be replaced should I get it put back on that new pipe. Or put it in the standard position where the standard bov still remains? If I put it on the new cooler pipe should I leave the standard blow off valve the way it is? It has a metal plate between it and the inlet pipe.

mad082 Grand Master

mad082

Posted
Posted

unless there is more piping for your fmic kit that what is show, you won't be replacing the pipe where the bov is. the pipe from the turbo to the stock intercooler will still be used, as will the pipe with the bov on it. the 3 bits of pipe shown go from where the stock intercooler sits to the fmic, and then the other 2 go from the fmic to the side fire wall and the next from the side firewall to the pipe with the bov on it.

as for the bov, just get an adapter. the best plave to have a bov fitted is as close to the throttle body as possible. it keeps the air flowing in the one direction.

moonus Experienced

moonus

Posted
Posted
unless there is more piping for your fmic kit that what is show, you won't be replacing the pipe where the bov is. the pipe from the turbo to the stock intercooler will still be used, as will the pipe with the bov on it. the 3 bits of pipe shown go from where the stock intercooler sits to the fmic, and then the other 2 go from the fmic to the side fire wall and the next from the side firewall to the pipe with the bov on it.

as for the bov, just get an adapter. the best plave to have a bov fitted is as close to the throttle body as possible. it keeps the air flowing in the one direction.

what he said, u wont need to replace the pipe that the BOV is connected to ;)

Jamie88 Community Regular

Jamie88

Posted
  • Author
Posted
unless there is more piping for your fmic kit that what is show, you won't be replacing the pipe where the bov is. the pipe from the turbo to the stock intercooler will still be used, as will the pipe with the bov on it. the 3 bits of pipe shown go from where the stock intercooler sits to the fmic, and then the other 2 go from the fmic to the side fire wall and the next from the side firewall to the pipe with the bov on it.

as for the bov, just get an adapter. the best plave to have a bov fitted is as close to the throttle body as possible. it keeps the air flowing in the one direction.

The pipe in the top of the front mount kit shown is the pipe that replaces the one my bov is on, and joins to the pipe off the throttle body. Correct me if Im wrong but pretty sure thats right. All the kits, ive seen, cheap ones included join there, run across the fan shroud area and down the side that currently has no pipes (right hand side of car). Which then joins onto one on the right hand side of cooler and the left hand side pipe joins to standard pipe which then runs to turbo??? Can anyone confirm this.?

moonus Experienced

moonus

Posted
Posted
The pipe in the top of the front mount kit shown is the pipe that replaces the one my bov is on, and joins to the pipe off the throttle body. Correct me if Im wrong but pretty sure thats right. All the kits, ive seen, cheap ones included join there, run across the fan shroud area and down the side that currently has no pipes (right hand side of car). Which then joins onto one on the right hand side of cooler and the left hand side pipe joins to standard pipe which then runs to turbo??? Can anyone confirm this.?

no you dont replace that bit.

mad082 Grand Master

mad082

Posted
Posted
The pipe in the top of the front mount kit shown is the pipe that replaces the one my bov is on, and joins to the pipe off the throttle body. Correct me if Im wrong but pretty sure thats right. All the kits, ive seen, cheap ones included join there, run across the fan shroud area and down the side that currently has no pipes (right hand side of car). Which then joins onto one on the right hand side of cooler and the left hand side pipe joins to standard pipe which then runs to turbo??? Can anyone confirm this.?

i'm assuming that you are talking about the pipe with the bracket on it? that bracket bolts to the drivers side of the motor near the injector rail. it runs from under the radiator hose on the drivers side to the start of the pipe with the bov on it. the pipe on the left of the cooler in the pic you posted runds from the drivers side of the cooler, through the holoe you have to cut in the side firewall, to the start of the pipe i just mentioned. the pipe on the right of the cooler runs from the where the stock cooler sits (so it joins the stock pipe that comes from the turbo) to the passenger side of the fmic.

mad082 Grand Master

mad082

Posted
Posted
The pipe in the top of the front mount kit shown is the pipe that replaces the one my bov is on, and joins to the pipe off the throttle body.

i think he is a bit confused as to what goes where.

either way, just get an adapter and mount the blitz bov on the stock bov's location.

bubba Grand Master

bubba

Posted
Posted (edited)
i think he is a bit confused as to what goes where.

either way, just get an adapter and mount the blitz bov on the stock bov's location.

I think you are confused.. he is talking about the COLD pipe coming from the stock cooler, it has his Blitz BOV attached to it. THIS pipe will be replaced by the piping in the kit, he is asking if he should try put his Blitz BOV in the same spot that it currently is or put it on the crossover pipe where the stock BOV sits.

I've seen adaptors for RB20/25's are my local Malz (our version of Autobarn), bolts in the stock location and has a 90deg bend in it. My R2D2 was actually mounted inside the front right guard.. well out of the way of prying police eyes :action-smiley-069:

Edited by bubba

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      R33 GTR running -9 with no tune

      By joshuaho96 · Posted

      Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I would say no, why, because my daughter, who also lives in Goulburn, hasn't recommended us going there Pity, as we miss all the German joints around in Sydney, actually, the restaurants are the only thing I really miss about Sydney, and a special mention to Ishibanboshi at Bondi Junction, their Kara-age Don is heart cloggingly deliciousness (always added a special boiled egg...or 2) 😋 
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      Does that German restaurant still exist in the old place out the NW end of Goulburn? When I say "out the NW end of"...I am really being vague. It was 1997 when I was last there, and the only point of reference I can recall is that it was on the opposite side of the main drag from the big merino. And when I say "opposite side of the main drag", I don't mean "on the main drag". It was either a couple of streets back from there, or might have even been out in the sticks a bit further. Was an old farm building or mill or somesuch. And when I say "the big merino" I might actually be thinking of a completely different part of town, because I just looked on maps and the big bugger is not where I remembered him to be! The food was good, consisting largely of various German mystery-meat sausage/loaf things and kartofflen.
    • GTSBoy
      R33 GTR running -9 with no tune

      By GTSBoy · Posted

      So while the second sentence is completely correct and the whole point of the conversation, the first sentence bears consideration. If this bloke is just hoping to throw big turbos on and drive it around, because there are no helpful facilities at all in his tropical paradise** then he likely has zero chance of even knowing what the TP is on the last column in the stock maps, let alone know whether the ECU is operating anywhere near it or past it. So the point is very very moot. And, per what I said before, at stock boost on those turbos, you may well be off the end of the map. **I'm just back from Vanuatu, so I know exactly what small Pacific nations can be like wrt paradise without requisite facilities. But it's not even that simple. I put a high flow on my car and had to drive it around without a proper tune because of the lack of opportunity*** to put the bigger AFM and injectors into it to allow it to be tuned. I had to turn the boost down to less than I had before, and back off the boost controller's ramp, because it was exploring parts of the map that it didn't drive in before, and really couldn't access for tuning on the dyno either, and so was pinging. It was still well within the last column, because when I first**** set up the Nistune on the Neo I rescaled all axes of the maps to give some more space to explore. ***Family dyno was broken ****This was 13 years ago, and the TIM thing wasn't a thing then and so TP would definitely grow when pushing past the stock tune's limits.
    • joshuaho96
      Squeaking clutch/throw out bearing

      By joshuaho96 · Posted

      Yep, this bit another local owner. I caught it before putting the transmission back into the car, what I noticed was the pressure plate fingers weren't flat and even. It's more obvious with the pull style clutch because the throwout bearing ring was visibly not flat once everything is put together. Nismo should really update their instructions to call out this specific detail. I'm not even sure the clutch as-shipped orients everything properly.
×
×
  • Create New...