Jump to content
SAU Community

Recommended Posts

There is a warning that flashes on my dash right beside the handbrake light and it looks like a "chevrolet" badge with wavey lines or steam coming off it. I have just recently had a replacement auto fitted and a bit of hyd fluid was lost from the back of the auto from a resevoir. It is still within the Min-Max range, not sure if this has anything to do with it. Automatic shop (very reputable) did not know what it is. It looks like an oil pump for the variable 4WD system, does this have anything to do with it. Has a 3 core radiator fitted, is this the overheat light, shouldn't be hot. Any ideas what this is.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/
Share on other sites

YEP, definetly number 12. I had to cut the temp sensor wire that comes out from under the mid floor to the second cat convertor. But that was a while ago. Should of seen the light since then. Thanks heaps for that info. Other than speaking Japlish, does anybody know what to do now.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3190743
Share on other sites

I am gonna go out on a limb and suggest its the attessa pressure cylinder that you are talking about? The pump for it is actually located at the back above the rear diff. The fill pot for it is inside the cargo area on the drivers side behnd one of the natty little panels in the side. As with all auto fluids, this should be checked with the car warm, running and parked on level ground. Do a search for the actual fluid required or have a look in the DIY sticky at the top of the forum.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3191431
Share on other sites

so maybe the O2 sensor is letting too much fuel in and causing it. It seems to be "heavier" again than it normally is. Like lucky to touch 300kms around town now just city driving. Used to get 350 - 400kms. So is this also measured at the o2 sensor aswell and whats the best replacement.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3191623
Share on other sites

The transfer case pump uses Auto trans fluid and is filled in the resoviour in the boot, the transfer case itself also uses ATF and is filled through a filler on the rear of the gearbox.

I think the engine check light can come on in circumstances other than just cat too hot right? If you've cut the wire it can't be cat temps....better check that out maybe search outside stagea section for it.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3193804
Share on other sites

Don't mean to hijack thread, but what warning is no.15? Mine came on everytime I got up to 160ish and released back to 100ish. Would stay on for anywhere between 5-15secs and then turn off. Also came on while stationary once.

You need to get a consult interface onto that to check the error codes... Most mechanics should have one and the stagea should be listed.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3201868
Share on other sites

There is a warning that flashes on my dash right beside the handbrake light and it looks like a "chevrolet" badge with wavey lines or steam coming off it. I have just recently had a replacement auto fitted and a bit of hyd fluid was lost from the back of the auto from a resevoir. It is still within the Min-Max range, not sure if this has anything to do with it. Automatic shop (very reputable) did not know what it is. It looks like an oil pump for the variable 4WD system, does this have anything to do with it. Has a 3 core radiator fitted, is this the overheat light, shouldn't be hot. Any ideas what this is.

that "chevy" looking light is surpose to be a pic of a cat conveter over heating. on my friends cars a s13, a cefiro and a cellcier all had this light come on, they all shared a comon problem. Bloocked Catilitic Conveter's. you can take yours out and either replace it. Smash the middle out with a screwdriver (illigal. 5 thousand dollar fine, but only if you get caught) or you can tap it on the ground to lossen the dirt and blow it out with compressed air. and get somone to hook that wire back on could be shorting out and making the light come on

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3205864
Share on other sites

The wire you are talking about seems to be a capillary/mechanical setup, so there is no rejoining it seeing as though it has been cut at the "cat". The light seems to have stopped again, I think I need to replace the O2 sensor anyhoos. Not getting a reading off the wires at the plug, except for the 12 v power wire. If it is the cat that is blocked, seems funny that the wire would give me a reading, unless it was the 02 sensor signalling the dash light.

Link to comment
https://www.sau.com.au/forums/topic/173642-warning-light/#findComment-3209677
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just wanted to unearth this and post my baby with the new front ❤️😝 Took her to my wedding rehearsal today. Next up is getting wide skirts (after wedding)
    • Yea, that is what I was getting at in my ramblings too. The nismo one actually is a 1.5 way and a 1 way. They don't do a *2* way because a true *2* way would have equal ramp angles. Or is that a true 1.5 way? Realistically I think a "1.5 way" does not actually exist. A diff can either lock in two directions or one. It also doesn't help that a LOT of people in Australia speak about 1.5 way diffs are referring to their 1 way diff.
    • Well, the trouble with that ^^ is: The configuration shown is absolutely a 1-way, not a 1.5-way. There is no way that a 1.5-way can be said to offer LSD action only on acceleration. If Nismo cannot get that right, then it is impossible to believe their documentation. That ^ is not a 1.5 way setup. That is a 1-way.   And so now I have allowed all doubts to flourish and have gone back to look at the MotoIQ video. I originally made the mistake of believing him when he said "this is a 1.5-way" at the ~6:10 mark. Because what he did was take the gear assembly out of the 2-way opening and just rotate it one place to the left to drop it into the 1-way opening. When he dropped it in there, the cam was "backwards" compared to the correct orientation shown in all other photos of that config. The flat shold have been facing the 1° ramp side of the opening, not the 55° ramp side. And I thought, "gee that's cute", but I was concerned at the time, when he put the other ring back on, that the gap between the rings looked like it was wider then in the 2-way config. And then I said a lot of things in my long post on Tuesday that could only make sense if the guy from MotoIQ was correct about what he'd done. BUT... I have now done my homework. I grabbed a frame of the video with the 2-way config, and then grabbed another with the "1.5-way" config, snipped out the cam and opening of that frame and just pasted it direct on top of the 2-way config. I scaled it so that the triangular opening was almost exactly the same height in both. AND.... the gap between the plates is wider with the cam installed in the triangualr opening backwards. That is.... it cannot go together that way. There would be massive force on the plates all the time, if you could even reassemble it.  So, My statement on the matter? The Nismo diff is actually only a 2-way and 1-way. There is no 1.5-way option in it, regardless of what they say. Here's a photo of a real 1.5-way ramp opening from Cusco (along with the 1 way option). And the full set of 1 through 2 way options from their racing diff, which is not same-same as what we'd typically be using, but...the cams work the same. A little blurry, but it comes from this Cusco doc, which is quite helpful. AND.... Cusco do in fact do what I suggested would be sensible, which is to have rings that do 1 and 1.5, and 1.5 and 2. Separately.  
    • Welcome Adam. Car looks great!
    • "With a 1.5-WAY, the LSD is effective only during acceleration."
×
×
  • Create New...