Jump to content
SAU Community

Recommended Posts

Hi members,

Spend a little money on your radiator to keep it in good running order

- you will be glad you did!

My car has recently been experiencing overheating issues.

I had just replaced the water pump and thermostat...

I got the radiator cleaned and serviced by NatRad - cost around $200 inc a pressure test, new top tank and O-ring seal.

(The normal price is about $100 if you don’t need a new tank)

The work involved removing the top tank and cleaning out the water galleries.

When you took off the radiator cap you could see some of the gunk causing the blockage - the radiator was 80% blocked!!

In my case the dude at the NatRad store (Perth - Morley) pointed out the top tank inlet was cracked - and he kept it to show me.

Any disturbance of the cooling system (heater core replacement, thermostat, water pump) will cause gunk to move in the cooling system and clog your radiator - think of the "gasket goo" that gets used to when replacing these components - if too much is used there is a good chance some of it will become mobile and clog the system.

Now that most skylines are ten + years in age, it’s a good idea to take the time to get it properly cleaned, besides just giving your cooling system a flush annually. It will keep your car running cooler and be more reliable.

Why not get a new radiator cap too? You can get standard 0.9 bar colour anodized ones from Repco for $12. Mine's red ;-)

And thanks to NatRad for your excellent quality of service.

Edited by negoshi8or
Link to comment
https://www.sau.com.au/forums/topic/173809-have-you-serviced-your-radiator/
Share on other sites

100 is fairly expensive. in my cars and my parents cars, I haven't really had any radiator blockage problems. I change the coolant regularly (2-3 years) with nulon extra long life (4 year coolant). No problems at all.

When they use gasket goo like on the waterpump etc, if the mechanic is good/normal, he'll use just the right amount of goo. Afterall, they don't exactly want to go squirting the whole tube in because it does cost money :bunny:

Its an easy job to do yourself and u can save the $200 for something else

Ummm... how is your post useful?

Unless you can tell members where to get a new top tank for free, a new top tank seal for free, and a pressure test for free...

Why bother posting???

because telling ppl to pay for a rad flush isnt helping anyone. Unless u need a new top tank replaced or pressure test, then a quick way to save some cash is to service your own rad system regularly, like manwhore has posted.

Ive seen numerous workshops show customers faulty parts that wasn't even on the customers car and say yes, we replaced this see here then proceed to charge a large repair bill.

The more things u do yourself the less likely u will get ripped.

Well of course the more you do yourself the less you get ripped - kinda obvious that one :)

FYI - it was not just a radiator flush - the top tank was removed and the galleries were physically cleaned out - so no I wasn't telling ppl to pay for a flush they can do themselves. I flushed the system and that didnt cure the problem - hence off to NatRad.

So if a cooling system flush doesnt cure you problems, more action is required.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...