Jump to content
SAU Community

Recommended Posts

i just got a fairly bare r32 rb26 with just the block, head, harmonic balancer, intake and exhaust manifolds no electrics left on it and its been sitting a while and dunno how manny k's its done so its gonna need a rebuild but i've already got a rb20 in my silvia is there any way i could rebuild the rb26 and still use the rb20 wiring harness and electrics, i got a heltec E8 ecu setup for the rb20 and i guess that can be adjusted for the extra displacement , any help would be appreciated

ok so i got the engine rebuilt and putting it all together now so is it possible to get this 26 running with my 20 harness and programed haltec ecu

help me out lads i think it will work i just need some backup :yes:

Edited by silvio
Link to comment
https://www.sau.com.au/forums/topic/174179-rb20-electrics-to-fit-rb26/
Share on other sites

ok so can i use the igniter and cam sensor from the rb20? and the harness cant be to much different even if i have to lengthen a few wires here and there

URAS what do u mean buy using the heltec loom cos this engine has no wiring harness at all all i got a rb20 harness to play with

the only problem i can see is the TPS depending on what you are going to use for an inlet manifold

i was thinkin that too but i'm hopeing the sensor will be similar even if i have to cut and solder the wires to fit if not iwas thinking of buying a greddy plenum or similar and puttin a 90mm throtle body on it

  • 9 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...