Jump to content
SAU Community

Did Dyno On Rb20det 449,8hp

impultion
 Share

Recommended Posts

Cubes Grand Master

Cubes

Posted
Posted

Nice Results..

Care to rattle off specs? Cams, headwork, turbo etc?

Would be nice to have those sort of dyno read outs from the DD Dyno's. :P

--------

To those that have replied; Whats with the nissansivlia.com type replies? Hearing a lot of it lately.

legend01 Experienced

legend01

Posted
Posted

Congratulations .

Good result, on an rb20det stock bottom end .I run an rb2.1det in my R32 and atm its making 306.1rwkw and its a handfull onhigh boost so take care on the street.I'm lucky i can turn the boost down which makes it good to drive on low boost

cheers Peter

CEF11E Veteran

CEF11E

Posted
Posted

Fantastic results. I bet you are really happy with it. that would be a lot of fun on long twisty roads

I am amazed at how well RB20's cope.

Have you done anything to the crank to drive the oil pump? that is a lot of revs for the stock pump otherwise.

If you could, please post this on the sticky in the forced induction for RB20's.

Cheers :D

impultion Contributor

impultion

Posted
  • Author
Posted
^^^ Yeah, rwkw is about ~15-20kw less than measured at the hubs.

If you've got a 3.6 final gear, you should probably look into getting the stock 4.363 in there, much better match for the RB20, covers up its lack of bottom end a bit and keeps it in top end more. Unless of course you regularly need to go over 300km/hr?

I have bought a 4.083 S15 final gear. Hope that will help

impultion Contributor

impultion

Posted
  • Author
Posted
Nice Results..

Care to rattle off specs? Cams, headwork, turbo etc?

Would be nice to have those sort of dyno read outs from the DD Dyno's. :)

--------

To those that have replied; Whats with the nissansivlia.com type replies? Hearing a lot of it lately.

Thanks for all replys, Yes I am pleased with the resaults. I have a RB26 crank with forged tomei pistons and eagle rods with I am putting in the RB20 this winter. Here are some specs.

Engine management:

Haltech E6X

Haltech 6-pack of coils

Mangnacore 10mm sparkwires

Bosch 203 ingnition module

Head:

Ported intake\exhaust

Jun high rev valve lifters

Jun valve springs

Jun 292 degree cams

Adjustable camgear (but they still stand on 0 mark)

Stock headgasket

ARP headstuds

Newly recoverd the head, new guides, seats etc

Bottem end:

Stock pistons\rods

ARP mainstuds and ARP 2000 rod bolts

ACL racebearings

Grex oilpump

N1 water pump

Nismo 62degree thermostat

Engine exterior:

JUN style inntake

90mm throttle body

Re-enforced "CHINA EBAY" 6-1 manifold

Turbonetics 60-1 A\R .63 exhaust housing

3" exhaust from turbo and back

Tial 38mm WG

4" Fmic with 3" piping

555cc injectors running 3Kg fuelpressaure

2x MSD fuelpumpes with catch

And thaths pretty much that. I am pleased with the resault only running @ 1.45bar of boost. Not sure how much power the stocl bottem end would hold up with, but I could easely have done 370KW@ the crank with 1.6bar boost, adjusted cam gears, and pulled 8500 insted of 8160RPM`s, but I dont know what the stock bottem end holds and I am the first in Norway to have a RB20DET with over 230Kw.

impultion Contributor

impultion

Posted
  • Author
Posted (edited)
Fantastic results. I bet you are really happy with it. that would be a lot of fun on long twisty roads

I am amazed at how well RB20's cope.

Have you done anything to the crank to drive the oil pump? that is a lot of revs for the stock pump otherwise.

If you could, please post this on the sticky in the forced induction for RB20's.

Cheers :(

Hi, since I`m not from the US or AU, I didint quite understand that one sentece: If you could, please post this on the sticky in the forced induction for RB20's.

?? :)

Edited by impultion
impultion Contributor

impultion

Posted
  • Author
Posted (edited)
Fantastic results. I bet you are really happy with it. that would be a lot of fun on long twisty roads

I am amazed at how well RB20's cope.

Have you done anything to the crank to drive the oil pump? that is a lot of revs for the stock pump otherwise.

If you could, please post this on the sticky in the forced induction for RB20's.

Cheers :)

Hi, I think I got it :(http://www.skylinesaustralia.com/forums/in...p;#entry3205064

Edited by impultion
impultion Contributor

impultion

Posted
  • Author
Posted (edited)
So it came with an RB20 standard in the S14?

If they did, they did what the should of done in Australia. Put in an RB20 instead of a SR20 :wave:

It came originally with SR20DET :(

All s13 in europe came with CA18DET

And all S14\S14a came with SR20DET

S15 and all skylines never made it to Norway, and they are impossible to get registrated on licens plates. :)

Edited by impultion
nisskid Grand Master

nisskid

Posted
Posted
Nice Results..

Care to rattle off specs? Cams, headwork, turbo etc?

Would be nice to have those sort of dyno read outs from the DD Dyno's. :)

--------

To those that have replied; Whats with the nissansivlia.com type replies? Hearing a lot of it lately.

+1 just appreciate the car ffs, dont need these RB20 is gay type posts

looks good mate btw.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...