Jump to content
SAU Community

Recommended Posts

safe = yes, if done correctly. none of this home cordless drill rubbish.

Ghetto modification is based on:

1 x Cordless drill

1 x Angle grinder and 1 x big f***k off disk

1 x big hammer

1 x crowbar

374m of electrical tape

867 x cable ties

Follow these simple steps and you WILL run 9s and drift like Tsuchia!

.. how do you think im so awesome!?!.. :)

EUG do you have msn, same as you GTS4WD, i'd like to have a chat about them.

Nah mate.. Dont have much time for it.. sorry..

but feel free to shoot me through a PM if you need anything :P

Calipars will fit without any problems..

make sure you bleed the brakes after playing around with them to ensure there isnt any air in the system

I still think unless your doing trackwork or full song through twisties a pair of awesome brake pads should be sufficient for street driving.. especially if you have ABS

  • Replies 200
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

867 x cable ties

I still think unless your doing trackwork or full song through twisties a pair of awesome brake pads should be sufficient for street driving.. especially if you have ABS

lol @ cable ties...

well i thought the idea to have more power was to do track work? i mean what good is 300HP when at the end of the day you're doing 100km/hr, same as the 50HP barina beside you on the freeway.

"well i thought the idea to have more power was to do track work? i mean what good is 300HP when at the end of the day you're doing 100km/hr, same as the 50HP barina beside you on the freeway." Lol that is funny, but also true, nah i'd like to update the brakes as well, i mean i have the parts sitting in my garage so why not?

How do i know if the braking system is ABS is there an easy way to tell?

I found out the my diff ratio is lower than a normal gts-t so i have alot of acceleration of the mark which is great. I would like to do a bit of track work, hillc climbs, circuit races and the odd run down the 1/4! So i think brakes should be done?

GTS4WD you said "Calipars will fit without any problems.. " Now is this with the new ghetto style rotors put on or the NA33 Rotors left on the car?

hame

GTS4WD you said "Calipars will fit without any problems.. " Now is this with the new ghetto style rotors put on or the NA33 Rotors left on the car?

hame

The calipars will fit in the DBA rotors without a problem.. just ensure that the with is the same on each..

then bobs your uncle.. well.. i dunno.. do you have an uncle called bob?

I would definately get DBA's if your planning on doing all of the things you want to do.. id suggest even get a set of slotted and drilled ones as an upgrade.. save you from buying them later and spending money now on stocko ones..

but thats just me.. :P

The calipars will fit in the DBA rotors without a problem.. just ensure that the with is the same on each..

then bobs your uncle.. well.. i dunno.. do you have an uncle called bob?

I would definately get DBA's if your planning on doing all of the things you want to do.. id suggest even get a set of slotted and drilled ones as an upgrade.. save you from buying them later and spending money now on stocko ones..

but thats just me.. :worship:

well actually i do have an unlce called bob which is kinda funny n weird! lol i like the sound of the drilled and slotted, but yeaha being a uni student money is rare, so i was thinking maybe just stock DBA rotors with gts-t calipers...its sufficent enough correct??

Any of you guys have an alternator for me!! i need one!

well actually i do have an unlce called bob which is kinda funny n weird! lol i like the sound of the drilled and slotted, but yeaha being a uni student money is rare, so i was thinking maybe just stock DBA rotors with gts-t calipers...its sufficent enough correct??

Any of you guys have an alternator for me!! i need one!

LOL!.. ahmen!.. I know the uni life..

You could lay off going full throttle for a while till you save the money and buy them..

*sigh*.. damn uni.. Im stuggling to see if I can find the funds to do my 3L bottom end..

P.s.. and thats just wreird about ur uncle..

Edited by GTS4WD

*hi5* to the uni club...

that is both weird and creepy about the uncle.

slotted dba/rda's are cheap as chips - you're only looking a few bucks more than the standard replacements (better again if you've got club sponsorship or group buy).

more than sufficient for any sort of mild application.

*hi5* to the uni club...

that is both weird and creepy about the uncle.

slotted dba/rda's are cheap as chips - you're only looking a few bucks more than the standard replacements (better again if you've got club sponsorship or group buy).

more than sufficient for any sort of mild application.

haha nice we all @ uni? crazy wat uni's we @? i''m @ griffith doing psychology, just finished my first year so i cheering. I fitted a new alternator today it stopped my squeeling problem (look in my topics) however it off another rb25de will this matter? everything seems to be going ok? tighened all the belts and everything better than they already were took it to pick up the miss's and she drove beautifully, problem solved! was fun lil job to do as well. As for the brakes going to get them a freshen up tomorow (The calipers anyway!) laterz...

Yeah.. As Eug said.. I really do thing slotted are the way to go.. its worth the extra ~$100.. even if you do have to wait till next pay cheak..

Uni - Bathurst CSU - Excerice science/Psychology..

Ahh for sure! bring on the mullah! i wanna see that 3ltr engine conversion Eugene!!

So your @ UQ! hmmm i was there last week doing a virtual driving study participation. i all finished uni for the year! yay Anyhow will clean up brakes tomorrow anything specific i can look for in them?

haha yeah i'd like to do it - but it'd have to be a project for a race car or something. as much as i like the RB motors, they are getting way too dated to keep up with all the new tech. i'd have to sink $10K to be happy with it.

what you can look for in the brakes:

- inspect rubber seals, no cracks etc. depends on how long they've been sitting around

- check for rust, pistons moving freely, nothing seized.

- make sure you have all the necessary pins and backing plates

- banjo bolts and nipples in good order

- make sure the calipers themselves have a good flush of fluid and aren't leaking

haha yeah i'd like to do it - but it'd have to be a project for a race car or something. as much as i like the RB motors, they are getting way too dated to keep up with all the new tech. i'd have to sink $10K to be happy with it.

what you can look for in the brakes:

- inspect rubber seals, no cracks etc. depends on how long they've been sitting around

- check for rust, pistons moving freely, nothing seized.

- make sure you have all the necessary pins and backing plates

- banjo bolts and nipples in good order

- make sure the calipers themselves have a good flush of fluid and aren't leaking

We should meet up some time Eugine have a chat about my brakes...

Cheak hoses and make sure their not perished, cuts etc.

or

slap some braided brake lines on too

:(

shit yeah, i would if it didn't cost an arm and a leg! i looking into the nismo ones but they are a fortune. I looking into braided lines for the engine bay too. no anyplace to get them cheap??

We should meet up some time Eugine have a chat about my brakes...

shit yeah, i would if it didn't cost an arm and a leg! i looking into the nismo ones but they are a fortune. I looking into braided lines for the engine bay too. no anyplace to get them cheap??

http://www.skylinesaustralia.com/forums/Ad...ak-t177690.html

I dont think its too bad..

If you need new lines.. do it.. plus its a sexy brake pedal feel afterwards.. definately worth it mate..

Excellent, i looked @ the details on it and realised it's a sunday great! i work usually from 8am-4pm whats the odds it had to be on a sunday i'll, do my best i suppose! really could like to meet some of you, also wanted to see how my car would go in the show-n-shine hehe

regards hame,

  • 2 weeks later...

Hey guys i know there is another thread open by PVA_glue about braking issues however since this is about my car, thought i'd keep it in my section, i have the gts-t front rotors drilled to 5-stud and the gts-t calipers. I don't have all the money in the world right now but i really would like to fit these breaks onto my car.

1. will the calipers (gts-t) fit on the GTS rotors? are the rotors too small in diameteR?

2. is it cheaper/better for my to just by blank DBA rotors drilled to 4stud, or redrill the 5-stud ones to suit 4 stud.

2. or should i do the whole thing (conversion) eg buy new hubs etc, this way i already have the rotors etc...

just something to keep the mind going....

regards hamo!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
    • Shock tower brace is in +5Kw....LOL  
×
×
  • Create New...